Yealink MeetingEye 400 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 278

Yealink MeetingEye 400 Скачать руководство пользователя страница 86

| Configuring Network Settings |

86

Parameter

Description

Configuration Method

Data Priority/

Data Priority (0-63)

Configure the DSCP
(Differentiated Services Code
Point) for data packets.

Note

: the default value is 63.

The greater the number is,
the higher the priority is. If
you change this parameter,
the system will reboot to
make the change take effect.

Web user interface

Endpoint

CTP20

Configuring MTU

Data packets that exceed the maximum transmission unit (MTU) size for any router or segment along the
network path may be fragmented or dropped, which may result in poor quality video at the receiving device.
You can set the maximum MTU size of the data packets sent by the system.

About this task

Configure the MTU size used in calls based on the network bandwidth settings. If the video becomes
blocky or network errors occur, packets may be too large; decrease the MTU. If the network is burdened
with unnecessary overhead; packets may be too small, increase the MTU.

Procedure

1.

Do one of the following:

• On your web user interface, go to

Network

>

Advanced

>

MTU

.

• On your VCS:

For MeetingEye 600/MeetingEye 400, go to

More

>

Setting

>

Network

>

Wired Network

>

Advanced Network

>

Network MTU (1000-1500)

.

For VC880/VC800/VC500/PVT980/PVT950, tap

MoreSetting

>

Advanced

>

Advanced Network

>

Network MTU (1000-1500)

.

For VC200, go to

More

>

Network

>

Wired Network

>

Advanced Network

>

Network MTU

(1000-1500)

.

For VP59, tap

Setting

>

Advanced

>

Advanced Network

>

Network MTU (1000-1500)

.

•

On your CTP20, tap

>

Setting

>

Network

>

Host Network

>

Advanced Network

>

Network

MTU (1000-1500)

.

2.

Configure and save the following settings:

«
...
84
85
86
87
88
...
»

Содержание MeetingEye 400























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды