manualshive.com logo in svg

YDOC ML 17 Series, Руководство пользователя

Поделиться
Скачать
YDOC ML 17 Series Скачать руководство пользователя страница 91

        ML-x17 DATA LOGGER MANUAL

 

Manufacturers of low power instruments

 

page 91

 

4.30.1.3

 

SD card test 

Use this feature to test the SD card. There will be data written on the card, and afterwards erased.  
Below a screenshot is given: 

 
 

The information from this test is very important. Not only the 
health of the SD card is tested, but also if there are some 
exception logged. Exceptions, where the watchdog was 
called to end a certain situation must NOT exist frequently. 
So, the size of the watchdog-file tells a lot about the 
operation of the system. 
 
 
 

4.30.1.4

 

Battery test 

This test is for evaluating the battery condition of Lithium Batteries only.  
The internal resistance is measured, by measuring the voltage of the cell, while increasing current 
consumption. A battery with an internal resistance of >1500 m ohms must be replaced. 

 

Since   the condition of rechargeable batteries 
changes with the state of charge, it is no use to 
test the batteries with this tool. Also, the internal 
resistance is in another region, so use this feature 
with lithium (LSH-20 form Saft) only! 
 
 
 
 
 
 
 

4.30.1.5

 

Comport redirect 

This feature allows the user to communicate with the sensor directly. It offers a transparent connection, 
from the USB terminal screen, to the sensor. Baud rate settings can be selected, to match the connected 
sensor. During the session, the sensor power switch of the data logger is enabled, to supply the sensor. 
So, a very convenient way of testing, troubleshooting, configuring your sensor is possible. 
Also comport redirect can be used for upgrading firmware of your sensor, through the data logger. The 
software package of the sensor can be used, after comport redirect is enabled. 
 
The following ports are possible: 

And the following baud rates / 
frame settings are supported: 

 
 
 
 

 
 
 
 

SD card test                                                                                                                                                     

                                                                                                                                                                 

Data log file size = 4578 KB                                                                                                                                     

Email file size    = 0 Bytes                                                                                                                                     

FTP file size      = 0 Bytes                                                                                                                                     

TCP file size      = 0 Bytes                                                                                                                                     

Watchdog file size = 162 

KB                                                                                                                                      

Free disk space    = 1896 MB                                                                                                                                     

File write/read OK                                                                                                                                               

                                                                                                                                                                 

Press any key! >                                                                                                                                                 

                                                                                                                                                                                                                

      

Battery test                                                                                                                                                     

                                                                                                                                                                 

Battery voltage = 3.585 

V                                                                                                                                        

Battery current = 57 mA                                                                                                                                          

                                                                                                                                                                 

Increasing power consumption...                                                                                                                                  

                                                                                                                                                                 

Battery voltage = 3.517 V                                                                                                                                        

Battery current = 157 mA                                                                                                                                         

                                                                                                                                                                 

Battery resistance = 680 mOhm                                                                                                                                    

                                                                                                                                                                 

Was the Battery test OK?                                                                                                                                         

Choose yes/no >                                                                                                                                                  

                             

Comport 

redirect                                                                                                                                                 

                                                                                                                                                                 

[0] Exit                                                                                                                                                         

[1] Serial 

port                                                                                                                                                  

[2] Accessory port                                                                                                                                               

[M] 

Modem                                                                                                                                                        

>                                       

Port mode                                                                                                                                                        

                                                                                                                                                                 

[0] 

Exit                                                                                                                                                         

[1] RS232 8N1                                                                                                                                                    

[2] RS485 

8N1                                                                                                                                                    

[3] SDI12                                                                                                                                                        

[4] RS232 7E1                                                                                                                                                    

[5] RS232 

8E1                                                                                                                                                    

[6] RS232 8O1                                                                                                                                                    

[7] RS485 8E1                                                                                                                                                    

[8] RS485 

8O1                                                                                                                                                    

[9] RS485 8N2                                                                                                                                                    

>                                                                                                                                                                

               

Содержание ML 17 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды