background image

English-

8

SAFETY INSTRUCTIONS

Disengage blades when not mowing. 
Shut off engine and wait for all parts to 
come to a complete stop before cleaning 
the machine, removing the grass 
catcher, or unclogging the discharge 
guard.

Operate machine only in daylight or good 
artificial light.

Do not operate the machine while under 
the influence of alcohol or drugs.

Watch for traffic when operating near or 
crossing roadways.

Use extra care when loading or 
unloading the machine into a trailer or 
truck.

Always wear eye protection when 
operating machine.

Data indicates that operators, age 60 
years and above, are involved in a large 
percentage of riding mower-related 
injuries. These operators should 
evaluate their ability to operate the riding 
mower safely enough to protect 
themselves and others from serious 
injury.

Follow the manufacturer’s 
recommendation for wheel weights or 
counterweights.

Anyone who operates this machine must 
first read and understand this Operation 
Manual. Local laws may regulate the age 
of the user.

Keep machine free of grass, leaves or 
other debris build-up which can touch hot 
exhaust / engine parts and burn. Do not 
allow the mower deck to plow leaves or 
other debris which can cause build-up to 
occur. Clean any oil or fuel spillage 
before operating or storing the machine. 
Allow machine to cool before storage.

WARNING!

Engine exhaust and certain 
vehicle components contain 
or emit chemicals considered 
to cause cancer, birth defects, 
or other reproductive system 
damage. The engine exhaust 
contains carbon monoxide, 
which is a odorless, colorless, 
poisonous gas. Do not use the 
machine in enclosed spaces.

Содержание ZEKW42170

















































































Отзывы: