YATO YT-82320, Инструкция по эксплуатации, Страница: 11 / 56

11
O R I G I N A L I N S T R U C T I O N S
GB
Do not leave the device unattended when it is connected to the power supply.
Do not overload the power cord. Do not use the power cord to carry the product, connect, or disconnect the plug from the power
socket. Avoid any contact between the power cord and heat sources, oil, sharp edges, and moving parts. Damage to the power
cord increases the risk of an electric shock. If the power cord is damaged (e.g. it is cut, its insulation is melted), immediately unplug
it from the socket, disconnect the cord from the product and return the power cord to an authorised service centre. It is not allowed
to use the product with a damaged power cord. It is not allowed to have the power cord repaired. It must be changed for a new
one at an authorised service centre.
Disconnect the power cord from the power socket, before installing, removing, or adjusting any of the product accessories.
Make sure that the selected accessory has been installed correctly, before starting the product.
Do not overload the product. The temperature of the housing must not exceed 60 O C. Overloading the product will accelerate its
wear and tear, lead to its damaging, and increase the risk of an electric shock.
Transport the water tank holding it only by the handle, the tank contains hot water, which can cause burns.
Hold only the handle of the steamer during operation, the steam escaping from the steamer is hot and may cause burns.
The product must be kept under supervision at all times during operation. Do not leave the product unattended if it is connected
to the power supply.
The product is not to be used by children. Keep the product and its power cord out of the reach of children. It is important to ensure
that children do not see the product as a toy.
Children should not be allowed to clean or maintain the product without the supervision of an adult.
Keep the device and its power cord out of reach of children under 8 years of age if it is connected to the power supply or when
it is cooling down.
This product cannot be used by people with impaired physical and/or mental abilities, and by people without any experience in or
understanding of the operation of the product, unless they are supervised or instructed in the safe use of the product, so that they
understand the relevant operating risks.
The water tank cannot be opened during use.
Do not use the device if it has been dropped, if there are visible signs of damage or if it is leaking.
Never point the steam jet at yourself, other people or animals. Contact with hot steam can cause serious burns. Never fi ll the
product with a substance other than clean water. In particular, do not use fl ammable substances such as alcohols, solvents. Do
not add any other substances, e.g. detergents, to the water.
PRODUCT OPERATION
Product assembly (II)
Note! Make sure that the product is disconnected from the power supply before assembly. The power cord should be disconnected
from the power socket and the device.
Screw one end of the hose to the hose connection on the tank and the other end to the steamer hose connection. Both connections
are of the same size and it does not matter which end of the hose is fi xed to the tank and which to the steamer. The hose should
be fi xed without using any tools. If the steam is noticed escaping from the connector during operation, tighten the connector.
Water fi lling and emptying (III)
Note! Make sure that the product is disconnected from the power supply before fi lling it with water or emptying. The power cord
should be disconnected from the power socket and the device. The product and the water stored in it must also be cooled.
Place the tank on a level, hard and fl at surface.
Unscrew the tank fi ller cap. Fill the tank with clean water. The front wall of the tank has indicators showing the minimum and
maximum water level in the tank. The minimum water level must not be lower than the MIN indicator and the maximum water level
must not be higher than the MAX indicator.
It is recommended to use the funnel to fi ll the tank, as this will minimise the risk of splashing water while fi lling the tank. Splashed
water should be thoroughly cleaned before connecting the device to the mains power supply.
After fi lling, fi t the tank inlet cap.
Caution! Never fi ll the tank by partially or completely submerging it in water.
After fi nishing operation, disconnect the product from the power supply by unplugging the power cord from the socket and then
the power cord from the device.
Wait until the product and the water remaining in the tank have cooled down completely. Unscrew the tank inlet cap, turn the tank
so that the inlet is facing downwards and empty the tank completely. Fit the tank cap.
If the tank cap is removed too early, hot steam or water can be released, which can cause serious burns.
Water quality
The tank can only be fi lled with clean water. If the running water is hard, in case of lack of knowledge contact your local water
supplier, use tap water and demineralised water mixture or only demineralised water. Heating hard water causes scale build-up,
which can lead to a decrease in capacity or even a complete clogging of the device.