YASKAWA VIPA System SLIO Скачать руководство пользователя страница 242

Страница: 242 / 380

10.4.5

Error behavior and interrupts

The system shows the following error behavior ...

... at gaps in the

‘slot’

configuration:

–

If the configuration of the I-Device contains gaps in the

‘slot’

configuration (i.e.

there are free

‘slots’

before used

‘slots’

), the configuration is rejected and

0xEA64 is returned as a configuration error in the diagnostic buffer.

–

If the configuration of the higher-level IO controller contains gaps in the

‘slot’

con-

figuration (i.e. there are free

‘slots’

before used

‘slots’

), the connection is rejected

with the PN IO Status

ErrorCode1

= 0x40 and

ErrorCode2

= 0x04

(AR_OUT_OF_RESOURCE).

... at modules, which differ from the configured:
–

ModuleDiffBlock

is generated and the wrong modules are not served.

... if the number of configured modules in the IO controller is greater than the number

of configured modules in the I-Device:
–

The IO controller receives a

ModuleDiffBlock

with ModuleStatus "NoModule" for

modules that are not configured in the I-Device. The I-Device sets the status of

the non-configured modules to "bad".

... if the number of configured modules in the I-Device is greater than the number of

configured modules in the IO controller:
–

The IO controller does not receive an error because the additional modules are

unknown.

Starting position

IO controller in RUN, I-Device in RUN

Event

I-Device CPU goes to STOP

Reaction

An OB 85 is called in the IO controller for each input and output transfer

area, which is located in the process image, if messages of process image

transfer errors are parametrized.

An OB 122 is triggered in the IO controller for each peripheral direct access

to an input or output transfer area.

Starting position

IO controller in RUN, I-Device in RUN

Event

IO controller goes to STOP

Reaction

An OB 85 is called in the I-Device for each input transfer area, which is

located in the process image, if messages of process image transfer errors

are parametrized.

In the I-Device, an OB 122 is triggered for each peripheral direct access to

an input transfer area.

Note: Output transfer areas can still be accessed!

Error behavior

VIPA System SLIO

Deployment PG/OP communication - PROFINET

Deployment as PROFINET I-Device > Error behavior and interrupts

HB300 | CPU | 013-CCF0R00 | en | 19-30

242

Содержание VIPA System SLIO





























































































































































































































































































































































































Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA VIPA System SLIO, Руководство пользователя

Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды