YASKAWA SI-T3 MECHATROLINK-II A1000 Series Скачать руководство пользователя страница 12

Страница: 12 / 46

YASKAWA ELECTRIC

TOBP C730600 86F YASKAWA AC Drive Option SI-T3 Installation Manual

3 Receiving

Receiving

After receiving the option package:

1. Make sure that the option is not damaged and no parts are missing. Contact your sales

outlet if the option or other parts appear damaged.

NOTICE:

Do not use damaged parts to connect the drive and the option. Failure to comply could damage

the drive and option.

2. Confirm that the model number on the option nameplate and the model listed in the

purchase order are the same. Refer to

Figure 2

on page

for details. Contact the

distributor where the option was purchased or contact Yaskawa or a Yaskawa

representative about any problems with the option.

Contents and Packaging

Table 2 Contents of Package

Installation Tools

• A Phillips screwdriver. Phillips screw sizes vary by drive capacity.

• A flat-blade screwdriver (blade depth: 0.4 mm (0.02 in), width: 2.5 mm (0.1 in)).

• A pair of diagonal cutting pliers.

• A small file or medium-grit sandpaper.

Description:

<1> GA700, GA800, CR700, and CH700 drives do not use the ground wire.

<2> GA700, GA800, CR700, and CH700 drives use two screws only.

Option

Ground

Wire

<1>

Screws

(M3)

LED Labels

Installation

Manual

1000-Series

GA500,

GA700,

GA800,

CR700, and

CH700

–

Quantity:

<2>

SI-T3

ERR

RUN

MANUAL

TOBP_C730600_86F_7_0_E.fm 12 ページ２０１８年１２月２０日　木曜日　午後６時１６分

Содержание SI-T3 MECHATROLINK-II A1000 Series















































Результаты поиска

Содержание SI-T3 MECHATROLINK-II A1000 Series

Отзывы:

Похожие инструкции для SI-T3 MECHATROLINK-II A1000 Series

Бренды по названию

Популярные бренды

YASKAWA SI-T3 MECHATROLINK-II A1000 Series, Руководство по установке

Результаты поиска

Содержание SI-T3 MECHATROLINK-II A1000 Series

Отзывы:

Похожие инструкции для SI-T3 MECHATROLINK-II A1000 Series

Бренды по названию

Популярные бренды