YASKAWA SGM7D-30F страница 392 Скачать руководство пользователя

Страница: 392 / 502

4.3 FT82 SERVOPACK with MECHATROLINK-III Communications References

4.3.1 List of Servo Parameters

4-67

Parameter Li

4.3

FT82 SERVOPACK with MECHATROLINK-III Communications References

The following table lists the parameters.

Note: Do not change the following parameters from their default settings.

•

Reserved parameters

•

Parameters not given in this manual

•

Parameters that are not valid for the Servomotor that you are using, as given in the parameter table

4.3.1

List of Servo Parameters

Parameter

No.

Size

Name

Setting

Range

Setting

Unit

Default
Setting

Applicable

Motors

When

Enabled

Classi-

fication

Refer-

ence

Pn000

Basic Function Selec-
tions 0

0000h to

10B1h

–

0000h

All

After

restart

Setup

–

Pn001

Application Function
Selections 1

0000h to

1142h

–

0000h

All

After

restart

Setup

–

Continued on next page.



Rotation Direction Selection

Reference

Use CCW as the forward direction.

Use CW as the forward direction. (Reverse Rotation Mode)





Reserved parameter (Do not change.)





Reserved parameter (Do not change.)

n.X



Reserved parameter (Do not change.)



Motor Stopping Method for Servo OFF and Group 1 Alarms

Reference

Stop the motor by applying the dynamic brake.

Stop the motor by the applying dynamic brake and then release
the dynamic brake.

Coast the motor to a stop without the dynamic brake.





Overtravel Stopping Method

Reference

Apply the dynamic brake or coast the motor to a stop (use the
stopping method set in Pn001 = n.



X).

Decelerate the motor to a stop using the torque set in Pn406 as
the maximum torque and then servo-lock the motor.

Decelerate the motor to a stop using the torque set in Pn406 as
the maximum torque and then let the motor coast.

Decelerate the motor to a stop using the deceleration time set in
Pn30A and then servo-lock the motor.

Decelerate the motor to a stop using the deceleration time set in
Pn30A and then let the motor coast.





Main Circuit Power Supply AC/DC Input Selection

Reference

Input AC power as the main circuit power supply using the L1, L2,
and L3 terminals (do not use shared converter).

Input DC power as the main circuit power supply using the B1/

and

2 terminals or the B1 and

2 terminals (use an external

converter or the shared converter).

n.X



Reserved parameter (Do not change.)

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды