YASKAWA S-V Seres Скачать руководство пользователя страница 54

Страница: 54 / 88

8 Set-up Procedure for Semi-closed Loop Control

8.2.3 Sigma-5 SERVOPACK Set-up with Linear Motor

8-10

*1 these settings are dependent on the applications

*2 in case of Pn080.0=1 (Disables hall sensor), the setting is not required

*3 this is only required when using Sigma-1 motors

8.2.3

Sigma-5 SERVOPACK Set-up with Linear Motor

According to applications, these parameters should be set for the correct operation of Sigma-5 with the option
modules.

Pn482

Polarity Detection Speed Loop Integral Time
[0.01 msec]

30.00

Immediately

Pn486

Polarity Detection Command Accel/Decel Time
[msec]

Immediately

Pn487

Polarity Detection Constant Speed Time [msec]

Immediately

Pn488

Polarity Detection Command Waiting Time
[msec]

100

Immediately

Pn490

Polarity Detection Load Level [%]

100

Immediately

Pn493

Polarity Detection Command Speed [min

-1

]

Immediately

Pn494

Polarity Detection Range [0.001 rev]

0.250

Immediately

Pn495

Polarity Detection Confirmation Torque Com-
mand [%]

100

Immediately

Pn498

Polarity Detection Allowable Error Range [deg.] 10

Immediately

Pn587

Polarity Detection for Absolute Scale Selection

Immediately

Does not detect polarity

Immediately

Detects polarity

Parameter

Function

Default
Value

Required
value

Cat.

When enabled

No.

Dig.

Parameter

Function

Default
Value

Required
value

Cat.

When enabled

No.

Dig.

Pn000

Basic Function Select Switch 0

Direction Selection

After restart

Forward command for forward direction

Forward command for reverse direction

Pn002

Application Function Select Switch 2

Absolute Encoder Usage

After restart

Uses absolute encoder as an absolute
encoder

Uses absolute encoder as an incremental
encoder

Pn00B

Application Function Select Switch B

Feedback Option Module Usage

After restart

Uses CN2 for external encoder feedback

Uses FB option for motor encoder feed-
back

Содержание S-V Seres

























































































Результаты поиска

Содержание S-V Seres

Отзывы:

YASKAWA S-V Seres, Руководство пользователя, Страница: 54 / 88

Результаты поиска

Содержание S-V Seres

Отзывы: