YASKAWA S-V Seres Скачать руководство пользователя страница 53

Страница: 53 / 88

8.2 Setup Procedure

8-9

Set-up Procedure for Semi-closed Loop Control

8.2.2

Sigma-5 SERVOPACK Set-up with Rotary Motor

According to applications, these parameters should be set for the correct operation of Sigma-5 with the option
modules.

Parameter

Function

Default
Value

Required
value

Cat.

When enabled

No.

Dig.

Pn000

Basic Function Select Switch 0

Direction Selection

After restart

Forward command for forward direction

Forward command for reverse direction

Pn002

Application Function Select Switch 2

Absolute Encoder Usage

After restart

Uses absolute encoder as an absolute
encoder

Uses absolute encoder as an incremental
encoder

External Encoder Usage

After restart

Do not use external encoder

Uses external encoder in forward rotation
direction

Reserved (Do not change.)

Uses external encoder in reversed rotation
direction

Reserved (Do not change.)

Pn00B

Application Function Select Switch B

Feedback Option Module Usage

After restart

Used for external encoder feedback

Used for motor encoder feedback

Pn080

Application Function Select Switch B

Hall Sensor Selection

After restart

Enables hall sensor

Disables hall sensor

Motor Phase Selection

After restart

Sets positive position feedback as phase
sequence of U, V, W

Sets negative position feedback as phase
sequence of U, V, W

Pn081

Application Function Select Switch 81

Encoder Pulse Output Usage

After restart

Enables the pulse output function (Pn281)

Disables the pulse output function

Coordination Setting between Origin and U-
phase position

After restart

Both positions are same

The positions are different

Hall Sensor Signal Inversion

After restart

Does not inverse the signals (Pos-Logic)

Inverses the signals (Neg-Logic)

Pn212

Encoder Output pulses [Pulse/Rev]

2048

After restart

Pn481

Polarity Detection Speed Loop Gain [0.1 Hz]

40.0

Immediately

Содержание S-V Seres

























































































Результаты поиска

Содержание S-V Seres

Отзывы:

YASKAWA S-V Seres, Руководство пользователя, Страница: 53 / 88

Результаты поиска

Содержание S-V Seres

Отзывы: