manualshive.com logo in svg

YASKAWA MOTOMAN DX100, Руководство по обслуживанию, Страница: 45 / 729

Поделиться
Скачать
YASKAWA MOTOMAN DX100 Скачать руководство пользователя страница 45

5

Replacing Parts

DX100

5.1

Replacing DX100 Parts

5-11

5.1.1.8

Replacing the Machine Safety Unit (JZNC-YSU01-1E)

Replacement Procedure

1. Disconnect all the cables connected to the machine safety unit.

*

Do not disconnect the terminating connectors (CBL-YRC020) at 

CN202 yet.
(Disconnect the ground wirings screwed to the front side of the unit.)

2. Loosen upper and lower side screws (4 places) fixing the machine 

safety unit to the controller.

3. Remove the machine safety unit from the controller by holding up 

upper and lower side cover.

4. Hook the new machine safety unit to the screws in the controller (4 

places).

5. Tighten upper and lower side screws (4 places) to fix the brake board.

6. Disconnect CN202 terminating connectors from the removed machine 

safety unit and connect them to the right side of CN202 on the new 
machine safety unit.

7. Connect all the disconnected cables.

*The flat cables connected to CN216 should be connected prior to 
connecting to CN214, CN213, CN212 and CN211.
(Connect the ground wirings firmly.)

Machine Safety Unit (JZNC-YSU01-1E)

FUSE

CN215

CN216

CN208

CN209

CN210

CN211

CN212

CN213

CN214

CN200

CN201

CN202

CN203

CN205

CN206

CN207

A

B

1

A

B

1

A

B

1

(CN202)

(CN203)

(CN200)

(CN201)

(CN205)

(CN206)

(CN207)

 I/F between AXIS board
 

Communication

 I/F between machine 
 safety units

F1,F2: Fuse

3.15A/250V

OT input connector

Power supply input 
connector    

Connector for power 
supply output      

(CN208)

Emergency stop button for the door

(CN209)

PP I/F

(CN215)

For connector 3 and 4 systems

(CN210)

(CN211)

ONEN

EXONEN

EXOT

(CN216)

MXT connection

FRC5-C50S52T-OLS(D20)

(CN212)

FANALM

FANCTL

LAMP

(CN213)

Contactor control 2

(CN214)

s

 I/F- IN

 I/F- OUT

 I/F between AXIS board
 

Contactor control 1

Содержание MOTOMAN DX100


























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов