YASKAWA MOTOMAN DX100 Скачать руководство пользователя страница 26

Страница: 26 / 729

Inspections

DX100

3.1

Regular Inspections

3-1

Inspections

3.1

Regular Inspections

Carry out the following inspections.

CAUTION

•

Do not touch the cooling fan or other equipment while the
power is turned ON.

Failure to observe this caution may result in electric shock or injury.

Inspection
Equipment

Inspection Item

Inspection

Frequency

Comments

DX100 Controller

Check that the doors
are completely
closed

Daily

Check for gaps or
damage to the
sealed construction

Monthly

Interior circulation
fan and backside
duct fan

Check operation

As required

While power ON

Emergency stop
button

Check operation

As required

While servo ON

Enable switch

Check operation

As required

In teach mode

Battery

Confirm battery
alarm or message is
displayed or not

As required

Power Supply

Check power supply
voltage is normal

As required

Circuit Breaker
Lead Cables

Check falling out,
loosing or breaking
of the lead cables
Check the correlate
voltage

As required

Содержание MOTOMAN DX100


























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MOTOMAN DX100

Отзывы:

YASKAWA MOTOMAN DX100, Руководство по обслуживанию, Страница: 26 / 729

Результаты поиска

Содержание MOTOMAN DX100

Отзывы: