YASKAWA LA500, Техническое руководство, Страница: 188 / 376

7.5 Minor Faults/Alarms
188 YASKAWA SIEPYEULA5001C LA500 Technical Manual
Code Name Causes Possible Solutions
Unsatisfactory balance between voltage phases. • Examine the supply voltage for problems.
• Make the drive input power stable.
• If the supply voltage is good, examine the magnetic contactor
on the main circuit side for problems.
The main circuit capacitors have become
unserviceable.
•
Examine the capacitor maintenance time in monitor U4-05
[CapacitorMaintenance] .
• If U4-05 is more than 90%, replace the capacitor. Contact
Yaskawa or your nearest sales representative for more
information.
• Examine the supply voltage for problems.
• Re-energize the drive.
•
If the alarm stays, replace the circuit board or the drive. For
information about replacing the control board, contact
Yaskawa or your nearest sales representative.
Note:
• The drive detects this error if the DC bus voltage changes irregularly without regeneration.
• If the drive detects this error, the terminal assigned to H2-01 to H2-03 = 10 [MFDO Function Select = Alarm] will be ON.
• Use L8-05 [Input Phase Loss Protection Sel] to enable and disable PF detection.
Code Name Causes Possible Solutions
SToF Safe Torque OFF Failure
One of the two terminals H1-HC and H2-HC
received the Safe Disable input signal.
The Safe Disable input signal is wired incorrectly.
• Make sure that the Safe Disable signal is input from an
external source to terminals H1-HC or H2-HC.
•
When the Safe Disable function is not in use, connect
terminals H1-HC and H2-HC.
There is internal damage to one Safe Disable
channel. Replace the board or the drive. For information about replacing
the control board, contact Yaskawa or your nearest sales
representative.
Note:
If the drive detects this error, the terminal assigned to H2-01 to H2-03 = 10 [MFDO Function Select = Alarm] will be ON.
Code Name Causes Possible Solutions
TiM Keypad Time Not Set There is a battery in the keypad, but the date and
time are not set. Set the date and time with the keypad.
Note:
• Parameter o4-24 [bAT Detection Selection] enables and disables TiM detection.
• If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.
Code Name Causes Possible Solutions
TrPC IGBT Maintenance Time (90%)
The IGBT is at 90% of its expected performance
life. Replace the IGBT or the drive. For information about replacing
the control board, contact Yaskawa or your nearest sales
representative.
Note:
If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.
Code Name Causes Possible Solutions
UL3 Undertorque Detection 1
A fault occurred on the machine.
Example: There is a broken pulley belt.
Examine the machine and remove the cause of the fault
The parameters are incorrect for the load. Adjust L6-02 [Torque Detection Level 1] and L6-03 [Torque
Detection Time 1] .
Note:
•
The drive detects this error if the drive output current is less than the level set in L6-02 for longer than L6-03 .
•
If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.
•
Set the conditions that trigger the minor fault using L6-01 [Torque Detection Selection 1] .
Code Name Causes Possible Solutions
UL4 Undertorque Detection 2 A fault occurred on the machine.
Example: There is a broken pulley belt.
Examine the machine and remove the cause of the fault
The parameters are incorrect for the load. Adjust L6-05 [Torque Detection Level 2] and L6-06 [Torque
Detection Time 2] .
Note:
• The drive detects this error if the drive output current is less than the level set in L6-05 for longer than L6-06 .
• If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.
• Set the conditions that trigger the minor fault using L6-04 [Torque Detection Selection 2] .
Code Name Causes Possible Solutions
Uv DC Bus Undervoltage
The drive input power voltage is changing too
much. • Use a better power supply voltage to align with the drive rated
voltage.
•
Make the drive input power stable.
•
If there is not a fault with the input power supply, examine the
magnetic contactor on the main circuit side for faults.
A phase loss occurred in the drive input power. Correct errors with the wiring for main circuit drive input power.
There is loose wiring in the drive input power
terminals. Examine for loose screws and tighten them as specified by the
tightening torque values in the manual.
There was a loss of power. Use a better power supply.