354
YASKAWA
SIEPC71061737B GA800 Drive Technical Reference
Code
Name
Causes
Possible Solutions
End8
HFI Alarm
•
Inductance saliency ratio (
E5-07
/
E5-06
) is too
small.
•
The drive cannot find the
n8-36 [HFI Frequency
Level for L Tuning]
value.
•
Set the correct value on the motor nameplate to
E5-xx [PM
Motor Settings]
or do rotational/stationary Auto-Tuning.
•
When it is necessary to set
n8-35 = 1 [Initial Pole Detection
Method = High Frequency Injection]
or
n8-57 = 1 [HFI Overlap
Selection = Enabled]
, make sure that there is no unusual noise in
the low speed range (10% or less) and that the motor does not
rotate in reverse at start.
Note:
If the drive detects
End8
, it will automatically set
n8-35 =0
[Pull-in] and n8-57 = 0 [Disabled]
. Do not change the settings
unless necessary.
Code
Name
Causes
Possible Solutions
End9
Initial Pole Detection Alarm
The drive cannot calculate the correct value for
n8-84
[Polarity Detection Current]
during High Frequency
Injection Tuning.
When
n8-35 = 1 [Initial Pole Detection Method = High Frequency
Injection]
or
n8-57 = 1 [HFI Overlap Selection = Enabled]
, make
sure that the motor does not rotate in reverse at start.
Note:
If the drive detects
End9
, it will automatically set
n8-35 =0
[Pull-in]
and
n8-57 = 0 [Disabled]
. Do not change the settings
unless necessary.
Code
Name
Causes
Possible Solutions
Er-01
Motor Data Error
The motor nameplate data entered during Auto-
Tuning is incorrect.
•
Make sure that the motor nameplate data is correct.
•
Do Auto-Tuning again and correctly set the motor nameplate
data.
The combination of the motor rated power and motor
rated current do not match.
•
Examine the combination of drive capacity and motor output.
•
Do Auto-Tuning again, and correctly set the motor rated power
and motor rated current.
The combination of the motor rated current that was
entered during Auto-Tuning and
E2-03 [Motor No-
Load Current]
do not match.
•
Examine the motor rated current and the no-load current.
•
Set
E2-03
correctly.
•
Do Auto-Tuning again, and correctly set the motor rated current.
The combination of the setting values of Motor Base
Frequency and Motor Base Speed do not match.
Do Auto-Tuning again, and correctly set the Motor Base Frequency
and Motor Base Speed.
Code
Name
Causes
Possible Solutions
Er-02
Drive in an Alarm State
The motor nameplate data entered during Auto-
Tuning is incorrect.
•
Make sure that the motor nameplate data entered in Auto-Tuning
is correct.
•
Do Auto-Tuning again and correctly set the motor nameplate
data.
You did Auto-Tuning while the drive had a minor
fault or alarm.
Clear the minor fault or alarm and do Auto-Tuning again.
There is a defective motor cable or cable connection.
Examine and repair motor wiring.
The load is too large.
•
Decrease the load.
•
Examine the machine area to see if, for example, the motor shaft
is locked.
The drive detected a minor fault during Auto-Tuning.
1.
Stop Auto-Tuning.
2.
Examine the minor fault code and remove the cause of the
problem.
3.
Do Auto-Tuning again.
Code
Name
Causes
Possible Solutions
Er-03
STOP Button was Pressed
During Auto-Tuning,
was pushed.
Auto-Tuning did not complete correctly. Do Auto-Tuning again.
Code
Name
Causes
Possible Solutions
Er-04
Line-to-Line Resistance Error
The Auto-Tuning results were not in the applicable
parameter setting range.
Auto-Tuning did not complete in a pre-set length of
time.
There is a defective motor cable or cable connection.
•
Examine and repair motor wiring.
•
Disconnect the machine from the motor and do Rotational Auto-
Tuning again.
The motor nameplate data entered during Auto-
Tuning is incorrect.
•
Make sure that the input motor nameplate data is correct.
•
Do Auto-Tuning again and correctly set the motor nameplate
data.
Содержание GA800 Series
