YASKAWA
SIEPC71061737B GA800 Drive Technical Reference
331
Code
Name
Causes
Possible Solutions
The torque compensation gain is too large.
Decrease the value set in
C4-01 [Torque Compensation Gain]
to
make sure that the motor does not stall.
The speed search-related parameters are set
incorrectly.
•
Examine the settings for all speed search-related parameters.
•
Adjust
b3-03 [Speed Search Deceleration Time]
.
•
Set
b3-24 = 1 [Speed Search Method Selection = Speed
Estimation]
after Auto-Tuning.
Phase loss in the input power supply is causing the
output current to change.
•
Correct errors with the wiring for main circuit drive input power.
•
Make sure that there is no phase loss, and repair problems.
Overload occurred during overexcitation deceleration.
•
Decrease the value set in
n3-13 [OverexcitationBraking (OEB)
Gain]
.
•
Decrease the value set in
n3-21 [HSB Current Suppression
Level]
.
Note:
•
The drive detects this fault if the electronic thermal protector of the drive started the drive overload protection.
•
Do a Fault Reset to clear the fault.
•
L5-07 [Fault Reset Enable Select Grp1]
disables the Auto Restart function.
Code
Name
Causes
Possible Solutions
oL3
Overtorque Detection 1
A fault occurred on the machine.
Example: The machine is locked.
Examine the machine and remove the cause of the fault.
The parameters are incorrect for the load.
Adjust
L6-02 [Torque Detection Level 1]
and
L6-03 [Torque
Detection Time 1]
settings.
Note:
•
The drive detects this fault if the drive output current is more than the level set in
L6-02
for longer than
L6-03
.
•
Do a Fault Reset to clear the fault.
•
If the drive detects this fault, it will operate the motor as specified by the Stopping Method set in
L6-01 [Torque Detection Selection 1]
.
•
L5-07 [Fault Reset Enable Select Grp1]
disables the Auto Restart function.
Code
Name
Causes
Possible Solutions
oL4
Overtorque Detection 2
A fault occurred on the machine.
Example: The machine is locked.
Examine the machine and remove the cause of the fault.
The parameters are incorrect for the load.
Adjust
L6-05 [Torque Detection Level 2]
and
L6-06 [Torque
Detection Time 2]
settings.
Note:
•
The drive detects this fault if the drive output current is more than the level set in
L6-05
for longer than
L6-06
.
•
Do a Fault Reset to clear the fault.
•
If the drive detects this fault, it will operate the motor as specified by the Stopping Method set in
L6-04 [Torque Detection Selection 2]
.
•
L5-07 [Fault Reset Enable Select Grp1]
disables the Auto Restart function.
Code
Name
Causes
Possible Solutions
oL5
Mechanical Weakening Detection 1
The drive detected overtorque as specified by the
conditions for mechanical weakening detection set in
L6-08 [Mechanical Fatigue Detect Select]
.
Do a deterioration diagnostic test on the machine side.
Note:
•
Do a Fault Reset to clear the fault.
•
If the drive detects this fault, it will operate the motor as specified by the Stopping Method set in
L6-08
.
Code
Name
Causes
Possible Solutions
oL7
High Slip Braking Overload
The load inertia is too large.
An external force on the load side rotated the motor.
Something is preventing deceleration on the load
side.
•
Decrease deceleration times in
C1-02, C1-04, C1-06, and C1-08
[Deceleration Times]
for applications that do not use High Slip
Braking.
•
Use a braking resistor to decrease the deceleration time.
The value set in
n3-04 [HSB Overload Time]
is too
small.
•
Increase the value set in
n3-04
.
•
Connect a thermal overload relay to the motor, and set
n3-04 =
1200 s (maximum value)
.
Note:
•
The drive detects this fault if the output frequency is constant for longer than
n3-04
.
•
Do a Fault Reset to clear the fault.
Содержание GA800 Series
