YASKAWA GA800 Series, Техническое обслуживание и устранение неисправностей

Страница: 122 / 566

2.5 Minor Faults/Alarms
122 YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
Code Name Causes Possible Solutions
PGo Encoder (PG) Feedback Loss
The encoder cable is disconnected or wired
incorrectly. Examine for wiring errors or disconnected wires in the encoder
cable, and repair problems.
The encoder is not receiving power. Examine the encoder power supply.
The holding brake is stopping the motor. Release the holding brake.
Note:
•
The drive detects this error if it does not receive the speed detection pulse signal from the encoder in the detection time set in F1-14 [Encoder Open-Circuit Detect Time] .
•
If the drive detects this error, the terminal assigned to H2-01 to H2-03 = 10 [MFDO Function Select = Alarm] will be ON.
•
If the drive detects this error, it will operate the motor as specified by the Stopping Method set in F1-02 [PG Open Circuit Detection Select] .
Code Name Causes Possible Solutions
PGoH Encoder (PG) Hardware Fault The encoder cable is disconnected. Correct any disconnected wires in the encoder cable.
Note:
• If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Select = Alarm] will activate.
• Parameters F1-20 [Encoder 1 PCB Disconnect Detect] or F1-36 [Encoder 2 PCB Disconnect Detect] enable and disable PGoH detection.
• If the drive detects this error, it will operate the motor as specified by the stopping method set in F1-02 [PG Open Circuit Detection Select] .
Code Name Causes Possible Solutions
rUn Motor Switch during Run
The drive received a Motor 2 Selection [H1-xx = 16]
during run.
Make sure that the drive receives the Motor 2 Selection while the
drive is stopped.
Note:
If the drive detects this error, the terminal assigned to H2-01 to H2-03 = 10 [MFDO Function Select = Alarm] will be ON.
Code Name Causes Possible Solutions
SE Modbus Test Mode Error MEMOBUS/Modbus communications self-
diagnostics
[H1-xx = 67] was done while the drive
was running.
Stop the drive and do MEMOBUS/Modbus communications self-
diagnostics.
Note:
If detected, the terminal assigned to H2-01 to H2-03 = 10 [MFDO Function Select = Alarm] will be ON.
Code Name Causes Possible Solutions
STo Safe Torque OFF
Safe Disable inputs H1-HC and H2-HC are open. • Make sure that the Safe Disable signal is input from an external
source to terminal H1-HC and H2-HC.
• When the Safe Disable function is not in use, use a jumper to
connect terminals H1-HC and H2-HC.
There is internal damage to the two Safe Disable
channels. Replace the board or the drive. Contact Yaskawa or your nearest
sales representative to replace the board.
Note:
• The drive will not output an alarm signal for this alarm.
• If the drive detects this error, the terminal set to H2-01 to H2-03 = 21 [MFDO Function Select = Safe Torque OFF] will activate.
Code Name Causes Possible Solutions
SToF Safe Torque OFF
One of the two terminals H1-HC or H2-HC received
the Safe Disable input signal.
The Safe Disable input signal is wired incorrectly.
• Make sure that the Safe Disable signal is input from an external
source to terminals H1-HC or H2-HC.
• When the Safe Disable function is not in use, use a jumper to
connect terminals H1-HC and H2-HC.
There is internal damage to one Safe Disable channel. Replace the board or the drive. For information about replacing the
control board, contact Yaskawa or your nearest sales representative.
Note:
If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.
Code Name Causes Possible Solutions
TiM Keypad Time Not Set
You put a battery in the keypad, but you have not set
the date and time. Set the date and time with the keypad.
Note:
•
Parameter o4-24 [bAT Detection Selection] enables and disables TiM detection.
•
If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.
Code Name Causes Possible Solutions
TrPC IGBT Maintenance Time (90%) The IGBT is at 90% of its expected performance life. Replace the IGBT or the drive. Contact Yaskawa or your nearest
sales representative for more information.
Note:
If the drive detects this error, the terminal set to H2-01 to H2-03 = 10 [MFDO Function Selection = Alarm] will activate.