3.2 Operating Procedures for Utility Functions
3.2.37 Program Table Initialization (FnB06)
3-120
*
If the
key is pressed in an operation prohibited state, “Error.” is displayed for
approximately 2 seconds and then the display returns to the JOG speed table editing
screen. In this case, make the setting again by referring to
3.2.37
Program Table Initialization (FnB06)
This function initializes the program tables and restores the settings on
shipment from the factory.
Preparation
Always check the following before you initialize a program table.
•
The parameters must not be write-prohibited (Fn010 must be set to
0000).
•
The program must not be running or on hold.
•
A program table save operation must not be in progress for any
means other than the digital operator.
•
Execution of the RES command must not be in progress.
3
Move the cursor with the
keys to select “STORE”.
Note: Selecting “CANCEL” and pressing
the
key will return the display
to the JOG speed table editing
screen.
4
Press the
key to start saving
the JOG speed table to flash mem-
ory.
*
Do not turn off the control power
supply until saving has been com-
pleted normally.
5
When saving to flash memory has
been completed normally, the dis-
play returns to the JOG speed table
editing screen.
6
Press the
key to return to the
Utility Function Mode main menu.
Continued from previous page.
Step
Operation
Result
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹑㹒㹍㹐㹃ࠉ㹈㹑㹎㹂ࠉ㹒㸿㹀㹊㹃㸽
ࠉࠉ㹁㸿㹌㹁㹃㹊ࠉ㹑㹒㹍㹐㹃
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹑㹲㹭㹰㹧㹬㹥ࠉ㹬㹭㹵㸬㸬㸬
㹎㹪㹣㹟㹱㹣ࠉ㹵㹟㹧㹲㸬
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹈㹑㹎㹂㸮㸮㸮㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸯㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸰㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸱㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸲ࠉ㹘㹍㹌㹃ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸳ࠉ㹈㹑㹎㹂ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸴ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸵ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲
