YASKAWA D1000 Series Скачать руководство пользователя страница 55

Страница: 55 / 251

3.4 Terminal Cover

YASKAWA ELECTRIC

TOEP C710656 07A YASKAWA Power Regenerative Converter - D1000 Instruction Manual

ical

lat

ion

◆

Models 2A0030 to 2A0130, 4A0030 to 4A0370 (IP00/Open Type Enclosure)

■

Removing the Terminal Cover

Loosen the screws on the terminal cover, then pull forward on the terminal cover to free it from the converter.

Note:

Models 2A0065 to 2A0130 and 4A0130 to 4A0630 have three mounting screws above the terminal cover.

CAUTION!

Do not completely remove the cover screws, just loosen them. If the cover screws are removed completely, the terminal

cover may fall off causing an injury.

Larger capacity converters have large and heavy terminal covers. Remove and attach these covers with care.

Figure 3.19

Figure 3.19 Removing the Terminal Cover on an IP00/Open Type Enclosure Model

■

Reattaching the Terminal Cover

After wiring the terminal board and other devices, double-check connections and reattach the terminal cover. Refer to

Wiring the Main Circuit Terminal on page 64

and

Wiring the Control Circuit Terminal on page 77

for details on

wiring.

Figure 3.20

Figure 3.20 Reattaching the Terminal Cover on an IP00/Open Type Enclosure Model

<1> Connect ground wiring first, followed by the main circuit, and then wire the control circuit. Power lines and

signal wiring exit through the opening provided.

<1>

Содержание D1000 Series




























































































































































































































































Результаты поиска

Содержание D1000 Series

Отзывы:

YASKAWA D1000 Series, Инструкция по эксплуатации, Страница: 55 / 251

Результаты поиска

Содержание D1000 Series

Отзывы: