background image

4

YASKAWA ELECTRIC

 TOBP C730600 41E 1000-Series Option DO-A3 Installation Manual

1  Preface and Safety

1

Preface and Safety

Yaskawa manufactures products used as components in a wide variety of industrial systems 

and equipment. The selection and application of Yaskawa products remain the responsibility 

of the equipment manufacturer or end user. Yaskawa accepts no responsibility for the way its 

products are incorporated into the final system design. Under no circumstances should any 

Yaskawa product be incorporated into any product or design as the exclusive or sole safety 

control. Without exception, all controls should be designed to detect faults dynamically and 

fail safely under all circumstances. All systems or equipment designed to incorporate a 

product manufactured by Yaskawa must be supplied to the end user with appropriate 

warnings and instructions as to the safe use and operation of that part. Any warnings 

provided by Yaskawa must be promptly provided to the end user. Yaskawa offers an express 

warranty only as to the quality of its products in conforming to standards and specifications 

published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS 

OFFERED. Yaskawa assumes no liability for any personal injury, property damage, losses, 

or claims arising from misapplication of its products.

Applicable Documentation

The following manuals are available for the option: 

Digital Output DO-A3 Option

Yaskawa 1000-Series Option

Digital Output DO-A3

Installation Manual (This book)

Manual No: TOBP C730600 41

Read this manual first.
The installation manual is packaged with the 
option and contains information required to install 
the option and set up related unit parameters.

Unit

Yaskawa AC Drive 1000-Series 

Quick Start Guide

The unit manuals cover basic installation, wiring, 
operation procedures, functions, troubleshooting, 
and maintenance information.
The manuals also include important information 
about parameter settings and unit tuning.
Access these sites to obtain Yaskawa instruction 
manuals:
U.S.: http://www.yaskawa.com
Europe: http://www.yaskawa.eu.com
Japan: http://www.e-mechatronics.com
Other areas: contact a Yaskawa representative.

Yaskawa AC Drive 1000-Series 

Technical Manual

D1000

Instruction Manual

DO

Содержание 1000-Series































Отзывы: