manualshive.com logo in svg

Yardbeast YB2050, Руководство оператора, Страница: 1 / 23

Поделиться
Скачать
Yardbeast YB2050 Скачать руководство пользователя страница 1

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wood Chipper Shredder

WARNING 

Read and follow all instructions in this manual before attempting to operate 

this machine. Please keep this manual available for consultation at any time. 

Read it thoroughly and become familiar with the operating instructions, 

maintenance and security indications. Failure to follow these instructions can 
result in serious injury to yourself and others.

3” 

 

www.yardbeast.com | (305) 396-3396 

Operator's Ma

1 

Wood Chipper Shredder 

Read and follow all instructions in this manual before attempting to operate 

this machine. Please keep this manual available for consultation at any time. 

Read it thoroughly and become familiar with the operating instructions, 

tenance and security indications. Failure to follow these instructions can 

result in serious injury to yourself and others.

 

 

Rederick Metal Industries Corp.  

1925 NW21st Terrace 

Miami, FL 33142 

YB2050 

Manual 

© 

Содержание YB2050
























Отзывы:

Нет отзывов