background image

     

MIG-29 Park Jet 

 

INSTRUCTION MANUAL   

 

 

 
 
 

                                                         
 
 
 
 
 
 
 
 
 
 
 
                             

 Warranty  

 

The contents of this kit are guaranteed to be free of defects at time and date of purchase. The warranty 

doesn’t cover modifications to kit, or damage to Components used in combination with this product. Yardbird 

RC will only cover the replacement of this kit for defects at time of purchase. 

                               

Liability 

 

Yarbird RC has 

NO

 control over final assembly of this product and or materials used in the final assembly  

process. YardBird RC assumes 

NO

 liability for the final user assembled product. 

The user of this product 

assumes all liability for the final assembly of this product and any damage caused in its operation 

and use

 

Please return this kit to the place of purchase in a new and unused condition for refund, if the purchaser is 

not prepared to accept liability for the operation and use of this product. 

 
 

 Read this assembly manual before starting construction. It contains Tips, and important 
construction instructions. Please read all information enclosed in this manual and     
information enclosed in products to be used in combination with this product. 

 
 

Wing Span:

 24 Inches. 

Length:

 34.5 Inches. 

Flying Weight: 

9.5-13.5 Ounces. 

Radio: 

Requires Three Channels, V-Tail Mixing.  

Recommended Motor: 

DUALSKY XM2826CA-12 Brushless Outrunner.  

 

YardBird RC                                                                                                                                                            
39 E. Gaslight PL                                                                                                                                                            
The Woodlands, TX 77382                                                                         

[email protected]                  

Phone/Fax: (281) 298 -5862

                                                                                            

Содержание MIG-29 Park Jet











Отзывы: