Yanmar SK1550 Скачать руководство пользователя страница 51

Страница: 51 / 99

Drive - 50

SK1550 Operator’s Manual

Start

Start

1. Ensure all controls are in neutral.
2. Set parking brake.
3. Activate accessories using ignition switch.
4.

If starting machine in normal conditions,

start engine and run at low throttle under light load for at

least one minute before applying heavier load.

If starting machine in cold weather:

1. Start engine.
2. Set parking brake.
3. Warm engine and hydraulic fluid by gradually increasing engine speed for up to 30 minutes.
4. After warmup, carefully operate all hydraulic controls at low throttle until controls operate as

described in controls chapter.

EMERGENCY SHUTDOWN

: Shut off machine or press remote engine stop button (if equipped).

Misuse of machine can cause death or serious injury.

Read and understand operator’s manual and all other safety instructions

before use. Know how to use all controls.

To help avoid injury:

• Allow hydraulic fluid time to warm before operating in cold weather. Cold hydraulic fluid can

lengthen ground drive stopping time.

• For starting in extreme temperatures, contact your Ditch Witch® dealer.

Pre-heater. Fire or explosion can cause death or serious

injury. Never use starter fluid.

NOTICE:

If engine turns but does not start within 10 seconds, allow starter to cool. Wait at least 30

seconds and try again.

Содержание SK1550




































































































Результаты поиска

Содержание SK1550

Отзывы:

Похожие инструкции для SK1550

Бренды по названию

Популярные бренды

Yanmar SK1550, Руководство оператора

Результаты поиска

Содержание SK1550

Отзывы:

Похожие инструкции для SK1550

Бренды по названию

Популярные бренды