Yanmar SA Series Скачать руководство пользователя

Страница: 84 / 170

10-3

10. 3-POINT HITCH AND DRAWBAR

SA221/324/424 Operation Manual

■

Hydraulic Flow Control/Stop Knob

(A) Hydraulic flow control/stop knob

(a) Knob turned counterclockwise:

• increases the rate of drop speed
• unlocks the hydraulic lift

(b) Knob turned clockwise:

• decreases the rate of drop speed
Knob turned clockwise until the knob stops turning:
• locks the hydraulic lift

●

Lowering the 3-point hitch too fast can lead to
accident or tractor failure.

●

Adjust the hydraulic flow control/stop knob:

• the time for lowering the implement from the

highest position to the lowest position, is 2
seconds or longer

●

Do not attempt to operate an implement on a
road.

●

While the tractor is traveling:

• keep the 3-point hitch control lever in the

raised position

• lock the 3-point hitch control lever with the

position stop knob

• do not fully close the hydraulic flow control/

stop knob

• closing the hydraulic flow control/stop knob

can cause damage to the hydraulic lift
circuit

●

During maintenance:

• do not use the hydraulic flow control/stop

knob as a means to keep the implements
raised

• loss of hydraulic pressure may cause the

implement to suddenly drop

• set the implement on solid blocks, or

remove the implement before starting any
maintenance

●

The hydraulic flow control/stop knob
determines the speed at which the lower link
is lowered.

IMPORTANT: Avoid damage!

●

Avoid attaching a heavy load to the 3-point hitch
when traveling on rough terrain.

• the hydraulic system may be damaged

●

Do not operate the 3-point hitch control lever
when the hydraulic flow control/stop knob is
closed.

• the preceding action can cause the

transmission hydraulic oil to overheat

! WARNING

(A)

(b)

(a)

10_3pointHitch.fm 3 ページ２０１８年７月６日　金曜日　午前９時４７分

Содержание SA Series











































































































































































Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды

Yanmar SA Series, Руководство по эксплуатации

Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды