Yanmar SA Series Скачать руководство пользователя

Страница: 133 / 170

14. PERIODIC SERVICE

14-21

SA221/324/424 Operation Manual

7. Pull down the sediment bowl to remove from the

separator body.

8. Remove the fuel filter from the sediment bowl.

Dispose of the fuel filter properly following
effective local law.

9. Remove the water and/or sediment found in the

sediment bowl.

10.Clean the sediment bowl with diesel oil.
11.Instal the fuel filter.
12.Install the sediment bowl.
13.Turn the sediment bowl locking collar clockwise

lock position.

14.Turn the fuel shut-off valve to the ON (open)

position.

15.Turn the starter key switch to START position.

Allow any trapped air to be bled from the fuel
system. If necessary, contact YOUR LOCAL
YANMAR TRACTOR DEALER for technical
assistance.

■

Service the Air Cleaner Element

1. Service the Air Filter

1. Park the tractor safely and securely.

• For details, see "7. Safe Practices for Parking the

Tractor" on page 1-7.

2. Shut off the engine.
3. Chock all the tires safely and securely.
4. Allow the engine to cool down for several

minutes.

5. Raise the hood.
6. Release the two latch hooks.

• The latch hooks secures the air cleaner canister

cover to the air cleaner canister.

(A) Latch hook
(B) Air cleaner canister
(C) Air cleaner canister cover
(D) Air filter

7. Unhook the latch hooks from the air cleaner

canister.

NOTE

●

Dispose the water and sediment together with
diesel fuel in the sediment bowl properly following
effective local law.

NOTE

●

The fuel system is self bleeding by turning the
starter key switch to "ON" position.

Avoid injury!
Remember that diesel fuel vapor is explosive
and flammable:

●

Touching hot surfaces can burn skin.

●

If the engine has been running for some time,
the engine components are hot including all
internal fluids.

●

Before performing maintenance or working
near the engine and engine parts:
• allow the engine to cool down
• always wear protective goggles and

protective clothing

! WARNING

IMPORTANT

A damaged air cleaner element can fail to prevent
dirt, dust and other contaminants from entering the
engine.

●

Always replace a contaminated, damaged and
cracked filter seal.

(B)

(C)

(A)

(D)

SA221_324_424_OperatorsManual.book 21 ページ２０１８年６月４日　月曜日　午後５時１９分

Содержание SA Series











































































































































































Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды

Yanmar SA Series, Руководство по эксплуатации

Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды