Yanmar 6LPA-STP2 Скачать руководство пользователя страница 38

Страница: 38 / 110

Adding Engine Oil

1. NOTICE: Prevent dirt and debris

from contaminating engine oil.

Carefully clean the dipstick and the

surrounding area before you

remove the cap. Remove the oil filler

port cap (Figure 6, (4)) from filler port

(Figure 6, (5)) and fill with engine oil.

2. Fill with oil to the upper limit on the

dipstick (Figure 6, (2)). NOTICE:

NEVER overfill the engine with

engine oil.

3. Insert the dipstick fully to check the

level. NOTICE: ALWAYS keep the oil

level between upper and lower lines

on the oil cap / dipstick.

4. Tighten the filler port cap securely by

hand.

MARINE DRIVE OIL

Note: Refer to the marine gear

manufacturer's operation manual for the

marine gear oil specifications. Refer to the

manufacturer's operation manual for marine

gear or stern drive oil specifications.

Mercruiser® Bravo Stern Drive

Oil Specifications

Use marine gear oil that meets or exceeds

the following guidelines and classifications:

Drive Oil

• QuickSilver

High Performance Gear

Lube.

Power Steering Oil (6LPA-STZP2 Only)

• Quicksilver

Power Trim and Steering

Fluid or Dexlone-II

Power Trim Oil

• Quicksilver

Power Trim and Steering

Fluid or SAE 10W-30 or 10W-40 Engine

Oil

QuickSilver is a registered trademark of Brunswick Corporation.

BEFORE YOU OPERATE

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды