Yanmar 3TNV82A Скачать руководство пользователя страница 64

Страница: 64 / 234

FAILURE DIAGNOSIS

1-62

TNV DI Service Manual

DTCs (Diagnostic Trouble Codes) General Description

Spare speed sensor (option)

(1) P1340/4: Failure with Spare Speed Sensor

DTC Detecting Conditions

Movement at Error occurrence

Estimation of Failure cause/Error condition

• The connector may not be properly connected.

• Output pulse voltage defect by low engine speed

• Output pulse defect by the battery over-charge

• Wiring defect of the harness

•

The spare speed sensor's signal wires may be disconnected or short-circuited with GND.

•

The alternator's terminals B and IG may be disconnected or short-circuited with GND.

• Output pulse defect by the alternator failure

• The E-ECU internal circuitry may be faulty.

DTC

P1340/4

Failure with Spare Speed Sensor

1 - Precondition; 2 - Detecting condition(s); 3 - Flashing pattern of failure indicator

Check points

1. Engine running.
2. Spare speed sensor signal below 0[min

-1

3. One flash followed by another flash.

Connector
Harness
alternator
E-ECU

Main speed sensor error detection

Unavailable

Available

Error Mode

[Run As Is]:
After detecting the error, the system lets
the engine continue to run without any
restrictions.

[Stop Immediately]:
The engine stops running.

Run restricted?

No.

Yes: The rack actuator relay is turned

OFF, and the rack position is forcibly
set to the engine stop position.

Recovery
Conditions

No.

Yes:Key switch START

Remarks

TNV_DI_SM_A4-Troubleshooting.book 62 ページ２００７年１１月１５日　木曜日　午後５時２７分

Содержание 3TNV82A











































































































































































































































Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды

Yanmar 3TNV82A, Руководство по устранению неисправностей

Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды