Yamato Pure Line WE200 Скачать руководство пользователя страница 14

Страница: 14 / 55

2. PRE-OPERATION PROCEDURES

Installation

8. Install the pre-process cartridge.

●

Turn power off and close water tap before installing or replacing the pre-process

cartridge.

●

Install procedure:

(1) Remove rubber cap from the process

cartridge.

(2) Place pre-process cartridge into

designated

bracket,

inside

the

WE200 unit. (See Figure 4)

(3) Connect the pre-process coupler,

“PWF OUT” to the “OUT” fitting on
the pre-process cartridge, while
sliding the light blue coupler tip back.
(See Figure 5 & 6)

(4) Connect the pre-process coupler,

“PWF OUT” to the “OUT” fitting on
the pre-process cartridge, while
sliding the light blue coupler tip back.
(See Figure 5 & 6)

●

Removal procedure:

(1) Remove the pre-process coupler

simply by holding it by the light blue
tip and pulling upward. (See Figure
6.)

(2) Remove from the

“IN” side first,

followed by the

“OUT” side.

Figure 4

Figure 5

Figure 6

※

Once pre-process hoses are installed, give each coupler a gentle tug to verify that they are

securely in place..

※

When removing pre-process couplers, water may drip from the pre-process cartridge fittings.
Be careful not to let water get on the leak sensor.

Slide

Coupler tip (blue)

Pre-process cartridge
bracket

Содержание Pure Line WE200
























































Результаты поиска

Содержание Pure Line WE200

Отзывы:

Yamato Pure Line WE200, Инструкция по эксплуатации, Страница: 14 / 55

Результаты поиска

Содержание Pure Line WE200

Отзывы: