Yamato IN604W Скачать руководство пользователя страница 28

Страница: 28 / 66

Operation Method

Input Program

Select program function



Check that the power in turned on.

PROGRAM

TROUBLE

ENTER

CANCEL

Select step

S01

Program OPR

①

Press the PROGRAM key. The program menu

starts and step number selection screen is
displayed.
Press the "

▼▲

". The registered step numbers

and  the  smallest  number  of  un-used  step  are
displayed  in  sequence.    Select  the  step  number
among them.



The "S01" is displayed when no program is

registered. In this case, the "

▼▲

" are invalid.

②

Press the ENTER key. The selected step

number is decided and the setting item selection
screen is displayed. The "Set TEMP" is
displayed first.

③

Press the CANCEL key to cancel the program

menu.

Edit step



The following four setting items are included in a step.



The unit operates with fixed rate inclination if the "START TEMP" and the "Set Temp" are different.

It enters into "Wait" if the temperature does not reach to the setting temperature within a setting
time.

Set Temp.

TEMP

TIME

Set Time

TEMP

START

(Operation with fixed rate inclination)

Setting item

Setting range

Setting temperature

Setting temperature range by product type

Setting time

0 minute to 999 hour and 59 minutes, End

Repeat initiating step

None, Registered step numbers 1 to 32

Repeat count

1 to 9999, Infinity

Содержание IN604W



































































Результаты поиска

Содержание IN604W

Отзывы:

Yamato IN604W, Инструкция по эксплуатации, Страница: 28 / 66

Результаты поиска

Содержание IN604W

Отзывы: