Yamato IN604W Скачать руководство пользователя страница 20

Страница: 20 / 66

Operation Method

Auto Stop Operation

As shown in the following figure, the device stops operating automatically by setting the timer.

Setting of the Auto Stop Operation

Turn on the power

POWER



Turn on the power switch of the unit (earth leakage

breaker).    Pressing the POWER key turns on the
power.    The  Main  Display  indicates  the
temperature  in  furnace.    The  Sub  Display
indicates "Standby" and the STANDBY lamp lights
on.

Select operation mode

MENU

①

Pressing the MENU key displays the operation

mode selection screen.

②

The Sub Display on the operation mode selection

screen displays the name of operation mode
currently

selected

with

blinking.

The

corresponding operation mode lamp blinks at the
same time.

③

Keep pressing the MENU key until the auto stop

operation mode is displayed.

④

Press the ENTER key. The auto stop operation

mode is decided.



The fixed temperature operation is selected at the

initial setting of unit. The operation mode carried
out last is selected in case other than it.

Operation

period

SV:

Setting temperature

Time

Set timer

▼

Activate timer

Start operation (manual)

Stop operation (auto)

Waiting

Содержание IN604W



































































Результаты поиска

Содержание IN604W

Отзывы:

Yamato IN604W, Инструкция по эксплуатации, Страница: 20 / 66

Результаты поиска

Содержание IN604W

Отзывы: