Yamatake SDC35, Руководство пользователя

Страница: 22 / 280

List of operation displays
Display Item Contents Initial value Setting value
Upper display: PV
Lower display: SP
PV SP(Target value) SP low limit to SP high limit 0
SP
LSP 1
(Display example) LSP group number 1 to LSP system group (Max. 4) 1
LSP (1st digit=the right end digit)
St 1-
(Display example) Step operation remaining Setting is disabled. –
Step No. time The step No. distinguishes up ramp,
Step remaining time down ramp, and soak.
PV MV (Manipulated Variable) -10.0 to +110.0% –
MV Setting is enabled in MANUAL mode
(Numeric value flashed)
HEAt
Heat MV (Manipulated Variable) Setting is disabled. –
Numeric value -10.0 to +110.0%
COOL Cool MV (Manipulated Variable) –
Numeric value
fb MFB (Motor opening feedback Setting is disabled. –
Numeric value value) +10.0 to +110.0%
Flashing when the value is 0.0 to 100.0% during estimate.
PV AT progress display Setting is disabled. –
At 1 (Display example) (1st digit=the right end digit)
Ct 1
CT current value 1 Setting is disabled. –
Numeric value
Ct2
CT current value 2 Setting is disabled. –
Numeric value
E 1 Internal Event 1 main setting -1999 to +9999U or 0 to 9999U 0
Numeric value
E 1. Sb Internal Event 1 sub setting
Numeric value
t 1. --
(Display example) Internal Event 1 remaining Setting is disabled. –
Numeric value time " ", is displayed at the right end digit when using
the ON delay time, and "L" , the OFF delay time.
E2
Internal Event 2 main setting Same as Internal Event 1 main setting 0
Numeric value
E2. Sb
Internal Event 2 sub setting Same as Internal Event 1 sub setting 0
Numeric value
t2. -- (Display example) Internal Event 2 remaining Same as Internal Event 1 remaining time –
Numeric value time
E3 Internal Event 3 main setting Same as Internal Event 1 main setting 0
Numeric value
E3. Sb
Internal Event 3 sub setting Same as Internal Event 1 sub setting 0
Numeric value
t3. --
(Display example) Internal Event 3 remaining Same as Internal Event 1 remaining time –
Numeric value time
L
[Mode bank]
List of parameter setting displays
Display Item Contents Initial value Setting value
A--M
AUTO/MANUAL
AUTO
: AUTO mode
MAN
: MANUAL mode AUTO
r--r
RUN/READY
RUN
: RUN mode
RDY
: READY mode RUN
l--r
LSP/RSP
lSp
: LSP
RSp
: RSP LSP
At
AT stop/start
At. OF
: AT stop
At. ON
: AT start AT stop
do Lt Release all DO latches Lt. ON : Latch continue Lt. OF : Latch release Latch continue
C. dI 1
Communication DI1
dI . OF
: OFF
dI . On
: ON OFF
*1 0: Unit of "1s" 1: Fixed at 0.5s 2: Fixed at 0.2s 3: Fixed at 0.1s
*2 5 to 120s when output includes the relay output
[SP bank]
[Event bank]
[PID bank]
[Parameter bank]
Display Item Contents Initial value Setting value
CtrL Control method 0: ON/OFF control 1: Fixed PID 0 or 1
At. OL
MV low limit at AT -10.0 to +110.0% 0.0
At. OH
MV high limit at AT -10.0 to +110.0% 100.0
dI FF
Differential (for ON/OFF control) 0 to 9999U 5
OFFS
●
ON/OFF control action point offset -1999 to +9999U 0