Yamatake HGC303 Скачать руководство пользователя страница 30

Страница: 30 / 130

Installation

Yamatake Corporation

2-10

Model HGC303 - Heat Value Gas Chromatograph

2-3-3 : HGM software installation

Installing the HGM

(1) Make sure Windows 98 / Me / NT / 2000 / XP has been installed.

(2) Insert the CD-ROM into the CD-ROM drive.

(3) Double-click on the [Setup HGM] folder.

(4) Double-click on the [setup] icon. The following screen will appear:

Figure 2-3 Setup message

Click on [OK] and the following display will appear:

Figure 2-4 HGM installation location

Default directory: C:\Program Files\hgm

If you want to use another drive or directory, select an optional drive or directory by
pressing the [Change Directory] button.

HGC Monitor Version 2.00 Setup

Welcome to the HGC Monitor Version 2.00 installation

program.

Setup cannot install system files or update shared files if they are in

use. Before proceeding, we recommend that you close any applications

you may be running.

Exit Setup

HGC Monitor Version 2.00 Setup

Begin the installation by clicking the button below.

Click this button to install HGC Monitor Version 2.00 software to the specified

destination directory.

Exit Setup

C:\Program Files\hgm\

Directory:

Change Directory

Содержание HGC303



































































































































Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды

Yamatake HGC303, Руководство пользователя

Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды