Yamaha YZF-R6T Скачать руководство пользователя страница 88

Страница: 88 / 111

PERIODIC MAINTENANCE AND MINOR REPAIR

6-42

EAU25080

Rear wheel

EAU25311

To remove the rear wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the axle nut.

2. Lift the rear wheel off the ground

according to the procedure on
page 6-39.

3. Remove the axle nut.
4. Loosen the locknut on each side of

the swingarm.

5. Turn the drive chain slack adjust-

ing bolts fully in direction (a) and
push the wheel forward.

6. Remove the drive chain from the

rear sprocket.

NOTE:

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

7. While supporting the brake caliper

bracket, pull the wheel axle out,
and then remove the wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAU25661

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the left-hand side.

1. Axle nut

2. Drive chain slack adjusting bolt

3. Locknut
4. Brake caliper

5. Brake caliper bracket

1. Wheel axle

U5SL12E0.book Page 42 Monday, August 9, 2004 10:51 AM

Содержание YZF-R6T
















































































































Результаты поиска

Содержание YZF-R6T

Отзывы:

Похожие инструкции для YZF-R6T

Бренды по названию

Популярные бренды

Yamaha YZF-R6T, Руководство пользователя

Результаты поиска

Содержание YZF-R6T

Отзывы:

Похожие инструкции для YZF-R6T

Бренды по названию

Популярные бренды