Yamaha YZ 2023 Series Скачать руководство пользователя страница 354

Страница: 354 / 378

TROUBLESHOOTING

9-7

EAM30512

TROUBLESHOOTING OF COOLING SYSTEM

Symptom

Possible cause

Actions

Overheating

Carbon buildup in piston head and

combustion chamber

Clean the piston head and com-

bustion chamber.

Clogged engine cooling water

passages

Check and clean the engine cool-

ing water passages.

Incorrect oil level

Adjust the oil level to the specified

level.

Incorrect oil viscosity

Change to recommended engine

oil.

Inferior oil quality

Change to recommended engine

oil.

Low coolant level

Add recommended coolant to the

specified level.

Damaged or leaking radiator

Replace the radiator.

Faulty radiator cap

Replace the radiator cap.

Clogged radiator fin

Clean the radiator fin.

Bent or damaged radiator fin

Repair the radiator fin or replace

the radiator.

Damaged or faulty water pump

Replace the water pump.

Damaged hoses or pipes

Replace the hose or pipe.

Improperly connected hoses or

pipes

Connect the hoses and pipes

properly.

Damaged throttle body joint

Replace the throttle body joint.

Loose throttle body joint

Tighten the throttle body joint bolts

to the specified torque.

Clogged air filter element

Clean or replace the air filter ele-

ment.

Brake drags

Check the brake system and

repair or replace faulty parts as

necessary.

Incorrect spark plug gap

Adjust to the specified spark plug

gap.

Incorrect spark plug heat range

Replace the spark plug with the

one of the specified type.

Faulty ECU

Replace the ECU.

Noise from water pump

Contact between the water pump

housing cover and impeller

Disassemble the water pump and

replace faulty parts.

Worn water pump housing bearing Replace the water pump housing

bearing.

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды