Yamaha YZ 2023 Series Скачать руководство пользователя страница 353

Страница: 353 / 378

TROUBLESHOOTING

9-6

EAM30511

TROUBLESHOOTING OF TRANSMISSION

Symptom

Possible cause

Actions

Difficult or impossible to shift

transmission gear

Clutch drags

Refer to “Clutch drags”.

Improperly adjusted shift rod

Adjust the shift rod installation

length.

Bent shift shaft

Replace the shift shaft.

Foreign object in a shift drum

groove

Remove foreign object from shift

drum groove.

Damaged shift drum

Replace the shift drum.

Seized shift fork

Replace the shift fork and shift fork

guide bar as a set.

Bent shift fork guide bar

Replace the shift fork guide bar.

Foreign object between transmis-

sion gears

Remove foreign object from trans-

mission gears.

Seized transmission gear

Replace the seized gear and the

axle as a set.

Improperly assembled transmis-

sion

Reassemble the transmission axle

assembly.

Jumps out of gear

Incorrect shift pedal position

Adjust the shift pedal position.

Improperly returned stopper lever

Replace the stopper lever spring.

Bent or worn shift fork

Replace the shift fork.

Shift drum incorrect axial play

Replace the shift drum.

Worn shift drum groove

Replace the shift drum.

Worn transmission gear dog

Replace the transmission gear.

Transmission noise

Damaged or worn transmission

gear

Replace the transmission gear.

Worn main axle spline

Replace the main axle.

Worn drive axle spline

Replace the drive axle.

Worn bearing

Replace the bearing.

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды