Yamaha YZ 2023 Series Скачать руководство пользователя страница 306 | Manualshive

Страница: 306 / 378

background image

FUEL INJECTION SYSTEM

8-19

EAM30352

ECU SELF-DIAGNOSTIC FUNCTION

The ECU is equipped with a self-diagnostic function in order to ensure that the fuel injection system is
operating normally. If this function detects a malfunction in the system, it immediately operates the en-
gine under substitute characteristics and illuminates the engine trouble warning light to alert the rider
that a malfunction has occurred in the system. Once a malfunction has been detected, a fault code
number is stored in the memory of the ECU.

•

To inform the rider that the fuel injection system is not functioning, the engine trouble warning light
flashes while the start switch is being pushed to start the engine.

•

If a malfunction is detected in the system by the self-diagnostic function, the ECU provides an appro-
priate substitute characteristic operation, and alerts the rider of the detected malfunction by illuminat-
ing the engine trouble warning light.

Engine trouble warning light indication and fuel injection system operation

* The engine trouble warning light flashes when any one of the following conditions is present and the

start switch is pushed:

Checking the engine trouble warning light

The engine trouble warning light comes on for around 2 seconds when pushing the start switch to turn
on the engine trouble warning light comes on while the start switch is being pushed.

Warning light indica-

tion

ECU operation

Fuel injection operation

Vehicle operation

Flashing*

Warning provided when

unable to start engine

Operation stopped

Cannot be operated

Remains on

Malfunction detected

Operated with substitute

characteristics in accor-

dance with the descrip-

tion of the malfunction

Can or cannot be oper-

ated depending on the

fault code

12:

Crankshaft position sensor

41:

Lean angle sensor

(open or short circuit)

30:

Lean angle sensor

(latch up detected)

50:

ECU internal malfunction

(faulty ECU memory)

33:

Ignition coil

(Malfunction detected in the primary wire of

the ignition coil)

a

b

c

d

c

a.  Start switch is not being pushed.
b.  Start switch is being pushed.
c.  Engine trouble warning light goes off
d.  Engine trouble warning light comes on for

around 2 seconds

«
...
304
305
306
307
308
...
»

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

COMFORT 10130810

Бренд: Contracor Страницы: 36

Бренд: HERO Страницы: 68

XRM125 CFT125 2020

Бренд: Honda Страницы: 111

Бренд: Suzuki Страницы: 101

Бренд: hepco & becker Страницы: 4

6304541 00 02 chrom

Бренд: hepco & becker Страницы: 6

Бренд: DYNATEK Страницы: 12

Бренд: Arai Страницы: 12

Бренд: Dayi Motor Страницы: 18

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 18

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 19

Бренд: R&G Страницы: 20

Бренд: R&G Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды