Yamaha YZ 2023 Series Скачать руководство пользователя страница 282

Страница: 282 / 378

THROTTLE BODY

7-7

EAM30271

CHECKING THE INJECTOR

1. Check:

•

Injector
Obstruction



Replace, and check the fuel

pump and the fuel injection system.
Refer to “FUEL INJECTION SYSTEM” on
page 8-17.
Deposits



Replace.

Damage



Replace.

2. Check:

•

Injector resistance
Refer to “CHECKING THE INJECTOR” on
page 8-59.

EAM30272

CHECKING THE THROTTLE BODY

1. Check:

•

Throttle body
Cracks/damage



Replace.

2. Check:

•

Fuel passages
Obstructions



Clean.

NOTICE

ECA26070

• Before removing the throttle body, clean

the area around the throttle body to prevent

dirt and other foreign material from falling

into the engine.

• If the throttle body is subject to strong

shocks or dropped during cleaning, re-

place it.

• Do not use any caustic carburetor cleaning

solution.

• Do not directly push the throttle valves to

open them.

• Do not loosen the throttle valve stopper

screw “1”, throttle valve pulley nut “2”,

throttle valve screw “3” or starter knob nut

“4”. A loss of performance may occur.

• Do not use compressed air to clean the

throttle body. Foreign materials may ad-

here to the intake air pressure sensor pas-

sage “a” and fuel injector “b” in the throttle

body.

3. Check:

•

Idle screw “1” passage “a”
Obstruction



Blow out with compressed air.

EAM30268

CHECKING THE FUEL PRESSURE

1. Check:

•

Fuel pressure
a. Remove the side cover (left/right), the seat

and the air scoop (left/right).
Refer to “GENERAL CHASSIS” on page
4-1.

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца, Страница: 282 / 378

Результаты поиска

Содержание YZ 2023 Series

Отзывы: