Yamaha YZ 2023 Series Скачать руководство пользователя страница 239

Страница: 239 / 378

CLUTCH

5-52

2. Install:

•

Right crankcase cover “1”

•

Right crankcase cover bolt “2”

TIP

Tighten the right crankcase cover bolts in stages
and in a crisscross pattern.

3. Install:

•

Push lever shaft “1”

TIP

•

Apply the lithium-soap-based grease on the oil
seal lip.

•

Before installation, apply the engine oil to the
bearings (upper side and lower side).

4. Install:

•

Primary driven gear “1”

•

Thrust washer “2”

•

Clutch boss “3”

•

Washer “4”

TIP

Apply the engine oil on the primary driven gear
inner circumference.

5. Install:

•

Conical washer “1”

•

Clutch boss nut “2”

NOTICE

ECA24660

Make sure to tighten to specification; other-

wise, it may damage the other part that is fas-

tened together.

TIP

•

Install the conical washer on the main axle with
the “OUT” mark “a” facing away from the vehi-
cle.

•

Apply engine oil to the threads and contact sur-
face of the clutch boss nut.

•

Apply engine oil to the contact surfaces of the
conical washer.

•

Use the clutch holder “3” to hold the clutch
boss.

•

Do not use an impact wrench for installing the
clutch boss nut.

•

Stake the clutch boss nut at cutouts “b” in the
main axle.

Right crankcase cover bolt

10 N·m (1.0 kgf·m, 7.4 lb·ft)

Clutch boss nut

95 N·m (9.5 kgf·m, 70 lb·ft)

Clutch holder

90890-04199

Universal clutch holder

YM-91042

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца, Страница: 239 / 378

Результаты поиска

Содержание YZ 2023 Series

Отзывы: