Yamaha YZ 2023 Series Скачать руководство пользователя

Страница: 213 / 378

VALVES AND VALVE SPRINGS

5-26

EAM30090

REMOVING THE VALVES

TIP

Before removing the internal parts of the cylinder
head (e.g., valves, valve springs, valve seats),
make sure that the valves are properly sealed.

1. Remove:

•

Valve lifter “1”

•

Adjusting pad “2”

TIP

•

Place a cloth in the timing chain space to pre-
vent adjusting pads from falling into the crank-
case.

•

Make a note of the positions of valve lifters and
adjusting pads so that they can be reinstalled
in their original places.

2. Check:

•

Valve sealing
Leakage at the valve seat



Check the valve

face, the valve seat, and the valve seat con-
tact width.
Refer to “CHECKING THE VALVE SEATS”
on page 5-28.
a. Pour a clean solvent “a” into the intake and

exhaust ports.

b. Check that the valves are properly sealed.

TIP

Check that there are no kerosene leaks from the
valve seat “1”.

3. Remove:

•

Valve cotter “1”

TIP

Remove the valve cotters by compressing the
valve spring with the valve spring compressor
“2” and the valve spring compressor attachment
“3”.

4. Remove:

•

Valve spring retainer “1”

•

Valve spring “2”

•

Valve “3”

•

Valve stem seal “4”

•

Valve spring seat “5”

TIP

Identify the position of each part very carefully so
that it can be reinstalled in its original place.

Valve lapper (ø14)

90890-04101

Valve lapper (ø14)

YM-A8998

Valve spring compressor

90890-04200

Valve spring compressor

YM-04019

Valve spring compressor attach-

ment

90890-04108

Valve spring compressor adapter

22 mm

YM-04108

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды