Yamaha YZ 2023 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 378

background image

IMPORTANT INFORMATION

1-9

EAM20089

IMPORTANT INFORMATION

EAM30009

PREPARATION FOR REMOVAL AND

DISASSEMBLY

1. Before the jobs, completely remove mud,

dust, and the like in order to prevent the entry
of them into the inside during the jobs.
Refer to “CARE” on page 1-29.

2. Use proper special tools and equipment. Re-

fer to “SPECIAL TOOLS” on page 1-15.

3. During disassembly, check and measure the

required parts, and make a record of them so
that you may refer to the record when install-
ing them. Moreover, arrange gears, cylin-
ders, pistons, and other parts for each section
so as not to confuse or lose them.

4. During disassembly, clean each of the parts,

and store them in trays for each section.

5. Flammable. Keep servicing areas away from

any source of fire.

6. During servicing, take special care not to re-

ceive an injury or a burn on the engine, the
exhaust pipe, the silencer, or the like.

7. If coolant is left adhered to the chassis, paint

and plating will be damaged. Therefore, rinse
it out with water in good time.

WARNING

EWA18970

Coolant is potentially harmful and should be

handled with special care.

• If it enters your eyes, wash it away with wa-

ter enough and then get medical attention

• If it splashes on your skin or clothes, quick-

ly wash it away with water and then with

soapy water.

• If it is swallowed, immediately induce vom-

iting and get medical attention.

EAM30010

REPLACEMENT PARTS

Make sure that the parts and grease or oil to be
used for repair of the vehicle, including periodic
replacement parts, are new YAMAHA genuine
parts and recommended parts.
Do not use any used parts, because these may
not be genuine though they have similar appear-
ances or because the quality may be changed
by aging.

EAM30011

GASKETS, OIL SEALS AND O-RINGS

1. When overhauling the engine, replace all

gaskets and O-rings. All gasket surfaces, oil
seal lips, and O-rings must be cleaned so that
there may be no dust on them.

2. During assembly, always apply proper oil to

bearings and proper grease to oil seal lips be-
fore installation.

«
...
19
20
21
22
23
...
»

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

Бренд: Xenith Страницы: 17

Бренд: S&B Filters Страницы: 7

Бренд: Qlink Страницы: 44

Бренд: Yoshimura Страницы: 3

Бренд: Sharper Image Страницы: 4

Бренд: X-lite Страницы: 84

HUSABERG MX 2000

Бренд: Ohlins Страницы: 16

Бренд: Honda Страницы: 127

Бренд: Ducati Страницы: 27

Бренд: R&G Страницы: 2

2008 V-Star 1300

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 100

2008 Fazer FZ1-N

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 399

2008 Fazer FZ1-N

Бренд: Yamaha Страницы: 546

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды