Yamaha YZ 2023 Series Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 378

background image

CHAIN DRIVE

4-68

EAM30075

REMOVING THE DRIVE CHAIN

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Place the vehicle on a maintenance stand so
that the rear wheel is elevated.

2. Remove:

•

Drive chain

TIP

Cut the drive chain with the drive chain cut & riv-
et tool. (Use goods on the market.)

EAM30076

CHECKING THE DRIVE CHAIN

1. Measure:

•

15-link section of the drive chain
Out of specification



Replace the drive

chain.

a. Measure the length “a” between the inner

sides of the pins and the length “b” be-
tween the outer sides of the pins on a 15-
link section of the drive chain as shown in
the illustration.

b. Calculate the length “c” of the 15-link sec-

tion of the drive chain using the following
formula.
Drive chain 15-link section length “c” =
(length “a” between pin inner sides +
length “b” between pin outer sides)/2

TIP

•

When measuring a 15-link section of the drive
chain, make sure that the drive chain is taut.

•

Perform this procedure 2–3 times, at a different
location each time.

2. Check:

•

Drive chain
Stiffness



Clean, lubricate, or replace.

3. Clean:

•

Drive chain
a. Wipe the drive chain with a clean cloth.
b. Put the drive chain in kerosene and re-

move any remaining dirt.

c. Remove the drive chain from the kerosene

and completely dry it.

NOTICE

ECA19090

• This vehicle has a drive chain with small

rubber O-rings “1” between the drive chain

side plates. Never use high-pressure water

or air, steam, gasoline, certain solvents

(e.g., benzine), or a coarse brush to clean

the drive chain. High-pressure methods

could force dirt or water into the drive

chain’s internals, and solvents will deterio-

rate the O-rings. A coarse brush can also

damage the O-rings. Therefore, use only

kerosene to clean the drive chain.

• Do not soak the drive chain in kerosene for

more than ten minutes, otherwise the O-

rings can be damaged.

15-link length limit

239.3 mm (9.42 in)

«
...
180
181
182
183
184
...
»

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

Бренд: Ohlins Страницы: 8

Бренд: Victory Motorcycles Страницы: 332

Бренд: Takegawa Страницы: 2

Бренд: R&G Страницы: 2

2006 G 650 Xmoto

Бренд: BMW Страницы: 132

Бренд: BMW Страницы: 88

Бренд: hepco & becker Страницы: 2

YZF-R1P 2001-2003

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 36

Бренд: Yamaha Страницы: 47

Бренд: Yamaha Страницы: 87

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды