Yamaha YZ 2023 Series Скачать руководство пользователя страница 158

Страница: 158 / 378

FRONT FORK

4-44

3. Remove:

•

Dust seal “1”

•

Stopper ring “2”
(with a flat-head screwdriver)

NOTICE

ECA14180

Do not scratch the inner tube.

4. Remove:

•

Inner tube “1”
a. Push in slowly “a” the inner tube just be-

fore it bottoms out and then pull it back
quickly “b”.

b. Repeat this step until the inner tube can be

pulled out from the outer tube.

5. Remove:

•

Base valve “1”
(from the damper assembly)

TIP

Hold the damper assembly with the cap bolt ring
wrench “2” and use the cap bolt wrench “3” to re-
move the base valve.

EAM30057

CHECKING THE FRONT FORK LEGS

1. Check:

•

Inner tube surface
Scratches



Repair or replace.

Use #1000 grit wet sandpaper.
Damaged oil lock piece



Replace.

•

Inner tube bends
Out of specification



Replace.

Use the dial gauge.

TIP

The bending value is shown by one half of the
dial gauge reading.

WARNING

EWA13650

Do not attempt to straighten a bent inner

tube as this may dangerously weaken it.

2. Check:

•

Outer tube
Scratches/wear/damage



Replace.

3. Measure:

•

Fork spring free length “a”
Out of specification



Replace.

Cap bolt wrench

90890-01500

Cap bolt wrench

YM-01500

Cap bolt ring wrench

90890-01501

Cap bolt ring wrench

YM-01501

Inner tube bending limit

0.2 mm (0.01 in)

Fork spring free length limit

492.0 mm (19.37 in)

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды