Yamaha YZ 2023 Series Скачать руководство пользователя страница 136

Страница: 136 / 378

FRONT BRAKE

4-22

TIP

Install the spring with a smaller inside diameter
to the brake master cylinder piston.

4. Install:

•

Brake master cylinder piston assembly “1”

•

Washer “2”

•

Circlip “3”

•

Dust boot “4”

•

Push rod “5”

TIP

•

Always install new brake master cylinder kit
“6”.

•

Before installation, apply brake fluid to the
components of the brake master cylinder pis-
ton assembly.

•

Before installation, apply silicone grease to the
push rod end.

•

Before installation, apply brake fluid to the in-
side of the brake master cylinder.

EAM30039

INSTALLING THE FRONT BRAKE MASTER

CYLINDER

1. Install:

•

Brake master cylinder “1”

TIP

•

Install the front brake master cylinder holder
with the “UP” mark facing up.

•

First, tighten the upper bolt, then the lower bolt.

2. Install:

•

Copper washer

•

Brake hose

•

Union bolt

WARNING

EWA13531

Proper brake hose routing is essential to in-

sure safe vehicle operation.

NOTICE

ECA24470

During installation, bring the brake hose into

contact with the brake master cylinder pro-

jection “a” and make its bent portion “b”

face downward.

TIP

Turn the handlebar toward right and left to make
sure that the brake hose does not touch other
parts (e.g., wire harness, cables, leads). Adjust
if necessary.

3. Pour brake fluid to the brake master cylinder

reservoir up to the specified level.

Brake master cylinder holder bolt

9 N·m (0.9 kgf·m, 6.6 lb·ft)

New

Brake hose union bolt

30 N·m (3.0 kgf·m, 22 lb·ft)

Specified brake fluid

DOT 4

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды