Yamaha YZ 2023 Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 378

background image

CHASSIS

3-25

Loose connection



Tighten the holder bolt.

3. Hold the vehicle upright and apply the rear

brake several times.

4. Check:

•

Brake hose
Brake fluid leakage



Replace the damaged

hose.
Refer to “REAR BRAKE” on page 4-24.

EAM30499

CHECKING THE BRAKE OPERATION

1. Check:

•

Brake operation
Brake not working properly



Check the

brake system.
Refer to “FRONT BRAKE” on page 4-13 and
“REAR BRAKE” on page 4-24.

TIP

Drive on the dry road, operate the front and rear
brakes separately and check to see if the brakes
are operating properly.

EAM30477

BLEEDING THE HYDRAULIC BRAKE

SYSTEM

WARNING

EWA19140

Bleed the brake system whenever:

• The system is disassembled.

• A brake hose is loosened, disconnected, or

replaced.

• The brake fluid level is very low.

• Brake operation is faulty.

1. Remove:

•

Brake master cylinder cap

•

Reservoir diaphragm

•

Reservoir float (front brake)

•

Protector (rear brake)

TIP

•

Be careful not to spill any brake fluid or allow
the reservoir to overflow.

•

Make sure that there is enough brake fluid be-
fore applying the brake. Ignoring this precau-
tion could allow air to enter the brake system,
considerably lengthening the bleeding proce-
dure.

•

If bleeding is difficult, it may be necessary to let
the brake fluid settle for a few hours. Repeat
the bleeding procedure when the tiny bubbles
in the hose have disappeared.

2. Bleed the brake system.

a. Fill the reservoir to the proper level with

the recommended brake fluid.

b. Install the reservoir diaphragm.
c. Connect the plastic hose “1” to the bleed

screw “2” securely, and place a container
under the end of the plastic hose.

d. Slowly apply the brake several times.
e. Fully pull the brake lever or fully press

down the brake pedal and hold it in posi-
tion.

f. Loosen the bleed screw.

TIP

Loosening the bleed screw will release the pres-
sure in the brake caliper and cause the brake le-
ver to contact the throttle grip or the brake pedal
to fully extend.

g. Tighten the bleed screw and then release

the brake lever or brake pedal.

h. Repeat steps (d) to (g) until all of the air

bubbles have disappeared from the brake
fluid in the plastic hose.

TIP

During the procedure, keep adding brake fluid to
the reservoir.

NOTICE

ECA24320

• Wipe off any brake fluid on the brake discs,

tires, wheels, etc.

• Brake fluid may erode painted surfaces or

plastic parts. Always clean up spilled fluid

A. Front
B. Rear

1

2

1

2

2

«
...
99
100
101
102
103
...
»

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

Бренд: R&G Страницы: 12

Бренд: APRILIA Страницы: 9

Бренд: GAS GAS Страницы: 119

Бренд: Honda Страницы: 61

6513515 00 22-00-40

Бренд: hepco & becker Страницы: 7

Бренд: Honda Страницы: 161

Бренд: Denali Страницы: 2

Бренд: Honda Страницы: 4

Бренд: hepco & becker Страницы: 2

Бренд: Cliftech Design Страницы: 24

Бренд: MARLINK Страницы: 3

WeldGuard ADF-206S

Бренд: Tanox Страницы: 16

Бренд: Petzl Страницы: 21

Бренд: Honda Страницы: 177

Бренд: hepco & becker Страницы: 2

Бренд: KTM Страницы: 18

Бренд: KTM Страницы: 14

350 EXC-F AUS 2012

Бренд: KTM Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды