manualshive.com logo in svg

Yamaha YXZ 1000RSS, Руководство пользователя

Поделиться
Скачать
Yamaha YXZ 1000RSS Скачать руководство пользователя страница 174

8-45

8

8. Install the tailpipe cover bolts and tighten

them to the specified torque.

EBU32460

Valve clearance

The correct valve clearance changes with
use, resulting in improper fuel/air supply or
engine noise. To prevent this, the valve clear-
ance must be adjusted regularly. This adjust-
ment  however,  should  be  left  to  a
professional Yamaha service technician.

EBU32470

Brakes

Replacement of brake components requires
professional knowledge. Brake service
should be performed by a Yamaha dealer.

WARNING

EWB02572

Operating with improperly serviced or ad-
justed brakes could lead to a loss in brak-
ing ability and an accident.

 

EBU35150

Checking the front and rear brake pads

Check each brake pad for damage and mea-
sure the lining thickness. If a brake pad is
damaged or if the lining thickness is less than
1.0 mm (0.04 in), have a Yamaha dealer re-
place the brake pads as a set.
The wheels need to be removed to check the
brake pads. (See pages 8-55, 8-57 for wheel
removal and installation procedures.)

Tightening torque:

Tailpipe cover bolt:

8 N·m (0.8 kgf·m, 5.9 lb·ft)

UB0F10E0.book  Page 45  Friday, October 27, 2017  2:03 PM

Содержание YXZ 1000RSS





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды