Yamaha YP125R Скачать руководство пользователя

Страница: 351 / 498

ELECTRIC STARTER (YP250R)

5-106

EAS24790

CHECKING THE STARTER MOTOR

1. Check:

• Commutator

Dirt

→

Clean with 600 grit sandpaper.

2. Measure:

• Commutator diameter “a”

Out of specification

→

Replace the starter

motor.

3. Measure:

• Mica undercut “a”

Out of specification

→

Scrape the mica to the

proper measurement with a hacksaw blade
that has been grounded to fit the commutator.

TIP

The mica of the commutator must be undercut to
ensure proper operation of the commutator.

4. Measure:

• Armature assembly resistances (commutator

and insulation)
Out of specification

→

Replace the starter

motor.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Measure the armature assembly resistances

with the digital circuit tester.

b. If any resistance is out of specification, re-

place the starter motor.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

5. Measure:

• Brush length “a”

Out of specification

→

Replace the brushes

as a set.

6. Measure:

• Brush spring force

Out of specification

→

Replace the brush

springs as a set.

Limit

22.4 mm (0.88 in)

Mica undercut (depth)

1.00 mm (0.04 in)

Digital circuit tester

90890-03174

Model 88 Multimeter with ta-
chometer

YU-A1927

Armature coil

Commutator resistance “1”

Continuity (0.0100–0.0140

Ω

20 °C (68 °F))

Insulation resistance “2”

No continuity (Above 1 M

Ω

at 20

°C (68 °F))

Limit

3.00 mm (0.12 in)

Brush spring force

7.75 N (790 gf, 27.90 oz)

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды