Yamaha YP125R Скачать руководство пользователя

Страница: 227 / 498

FRONT FORK

4-52

EAS22960

REMOVING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Cap bolt “1”

NOTICE

ECA37P1027

When removing the cap bolt, take care not to
damage the rectifier/regulator “2” with the
tools.

TIP

If the cap bolt is difficult to loosen, slightly loosen
the lower bracket pinch bolts “3”.

3. Loosen:

• Lower bracket pinch bolts

WARNING

EWA37P1022

Before loosening the lower bracket pinch
bolts, support the front fork leg.

EAS22980

DISASSEMBLING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Drain:

• Fork oil

TIP

Stroke the inner tube several times while drain-
ing the fork oil.

2. Remove:

• Dust seal “1”
• Oil seal clip “2”

(with a flat-head screwdriver)

NOTICE

ECA14180

Do not scratch the inner tube.

3. Remove:

• Damper rod bolt “1”
• Copper washer
• Damper rod

TIP

While holding the damper rod with the damper
rod holder “2” and T-handle “3”, loosen the
damper rod bolt.

Damper rod holder

90890-01294

Damping rod holder set

YM-01300

T-handle

90890-01326

T-handle 3/8" drive 60 cm long

YM-01326

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды