Yamaha YP125R Скачать руководство пользователя

Страница: 163 / 498

CHASSIS

3-36

EAS21260

CHECKING THE REAR BRAKE PADS
(YP250R)

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

• Rear brake pad

Wear indicator groove “a” has almost disap-
peared

→

Replace the brake pads as a set.

Refer to “REAR BRAKE” on page 4-29.

EAS21270

CHECKING THE FRONT BRAKE HOSE

1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Hold the vehicle upright and apply the front

brake several times.

3. Check:

• Brake hose

Brake fluid leakage

→

Replace the damaged

hose.
Refer to “FRONT BRAKE” on page 4-17.

EAS21290

CHECKING THE REAR BRAKE HOSE

1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Check:

• Brake hose holder “2”

Loose connection

→

Connect.

3. Hold the vehicle upright and apply the rear

brake several times.

4. Check:

• Brake hose

Brake fluid leakage

→

Replace the damaged

hose.
Refer to “REAR BRAKE” on page 4-29.

EAS21350

BLEEDING THE HYDRAULIC BRAKE
SYSTEM

WARNING

EWA37P1005

Bleed the hydraulic brake system whenever:
• The system is disassembled.
• A brake hose is loosened, disconnected or

replaced.

• The brake fluid level is very low.
• The brake operation is faulty.

TIP

• Be careful not to spill any brake fluid or allow

the brake master cylinder reservoir to overflow.

A. YP125R
B. YP250R

Содержание YP125R



















































































































































































































































































































































































































































































































Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды

Yamaha YP125R, Руководство по обслуживанию

Результаты поиска

Содержание YP125R

Отзывы:

Похожие инструкции для YP125R

Бренды по названию

Популярные бренды