Yamaha YFZ45YSSH Скачать руководство пользователя страница 144

Страница: 144 / 154

10-1

EBU25962

SPECIFICATIONS

Dimensions:

Overall length:

1795 mm (70.7 in)

Overall width:

1240 mm (48.8 in)

Overall height:

1065 mm (41.9 in)

Seat height:

810 mm (31.9 in)

Wheelbase:

1270 mm (50.0 in)

Ground clearance:

235 mm (9.3 in)

Minimum turning radius:

3600 mm (142 in)

Weight:

Curb weight:

184.0 kg (406 lb)

Noise and vibration level:

Noise level (77/311/EEC):

85.9 dB(A) at 3750 r/min (YFZ45YSSH,
YFZ45YSXH_EUR/FRA/GBR)

Uncertainty of measurement:

3.0 dB(A) (YFZ45YSSH, YFZ45YSXH_EUR/FRA/GBR)

A-weighted sound power level:

99.0 dB(A) at 3750 r/min (YFZ45YSSH,
YFZ45YSXH_EUR/FRA/GBR)

Uncertainty of measurement:

3.0 dB(A) (YFZ45YSSH, YFZ45YSXH_EUR/FRA/GBR)

Vibration on seat (EN1032, ISO5008):

Will not exceed 0.5 m/s² (YFZ45YSSH,
YFZ45YSXH_EUR/FRA/GBR)

Uncertainty of measurement:

0.1 m/s² (YFZ45YSSH, YFZ45YSXH_EUR/FRA/GBR)

Vibration on handle (EN1032, ISO5008):

Will not exceed 2.5 m/s² (YFZ45YSSH,
YFZ45YSXH_EUR/FRA/GBR)

Uncertainty of measurement:

0.8 m/s² (YFZ45YSSH, YFZ45YSXH_EUR/FRA/GBR)

Engine:

Engine type:

Liquid cooled 4-stroke, DOHC

Cylinder arrangement:

Single cylinder

Displacement:

449 cm³

Bore

stroke:

95.0

63.4 mm (3.74

2.50 in)

Compression ratio:

11.8 : 1

Starting system:

Electric starter

Lubrication system:

Dry sump

UBW260E0.book Page 1 Thursday, May 12, 2016 2:28 PM

Содержание YFZ45YSSH



























































































































































Результаты поиска

Содержание YFZ45YSSH

Отзывы:

Yamaha YFZ45YSSH, Руководство пользователя, Страница: 144 / 154

Результаты поиска

Содержание YFZ45YSSH

Отзывы: