Yamaha YFM70RSBG Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 160

Yamaha YFM70RSBG Скачать руководство пользователя страница 145

8-53

8

TIP

When installing the wheel, make sure its arrow
mark

points toward the rotating direction of

the wheel.

3. Lower the ATV to the ground.
4. Tighten the wheel nuts to the specified

torques.

EBU25741

Troubleshooting

Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the
fuel, compression, or ignition systems, for exam-
ple, can cause poor starting and loss of power.
The following troubleshooting charts represent
quick and easy procedures for checking these vi-
tal systems yourself. However, should your ATV
require any repair, take it to a Yamaha dealer,
whose skilled technicians have the necessary
tools, experience, and know-how to service the
ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.

WARNING

EWB02281

Do not smoke when checking the fuel system.
Fuel can ignite or explode, causing severe inju-
ry or property damage. Make sure there are no
open flames or sparks in the area, including pi-
lot lights from water heaters or furnaces.

1. Arrow mark

Tightening torques:

Front wheel nut:

45 Nm (4.5 m·kgf, 33 ft·lbf)

Rear wheel nut:

45 Nm (4.5 m·kgf, 33 ft·lbf)

U2LS61E0.book Page 53 Friday, April 17, 2015 8:25 AM

«
...
143
144
145
146
147
...
»

Содержание YFM70RSBG

































































































































































Отзывы:

Нет отзывов