Yamaha YFM70RSBG Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 160

Yamaha YFM70RSBG Скачать руководство пользователя страница 143

8-51

8

4. Place a new headlight bulb into position.

NOTICE:

Do not touch the glass part of the

headlight bulb to keep it free from oil, oth-
erwise the transparency of the glass, the
luminosity of the bulb, and the bulb life will
be adversely affected. Thoroughly clean
off any dirt and fingerprints on the head-
light bulb using a cloth moistened with al-
cohol or thinner.

[ECB00652]

5. Install the headlight bulb holder by pushing it

in and turning it clockwise.

6. Install the headlight bulb holder cover.
7. Place the headlight unit in the original posi-

tion, and then install the bolt.

8. Adjust the headlight beam if necessary.

EBU25562

Adjusting a headlight beam

NOTICE

ECB00691

It is advisable to have a Yamaha dealer make
this adjustment.

1. Headlight bulb holder

1

1. Do not touch the glass part of the bulb.

U2LS61E0.book Page 51 Friday, April 17, 2015 8:25 AM

«
...
141
142
143
144
145
...
»

Содержание YFM70RSBG

































































































































































Отзывы:

Нет отзывов