Yamaha YFM700RSBH Скачать руководство пользователя | Manualshive

Страница: 58 / 160

background image

5-4

5

EBU19542

Fuel

Make sure that there is sufficient fuel in the tank.
(See page 4-10.)

EBU19561

Engine oil

Make sure that the engine oil is at the specified
level. Add oil as necessary. (See page 8-13.)

EBU19632

Coolant

Make sure that the coolant is at the specified level.
Add coolant as necessary. (See page 8-17.)

TIP

The coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.

EBU19713

Front and rear brakes

Brake lever and brake pedal



Check that there is no free play in the brake le-
ver. If there is free play, have a Yamaha dealer
check the brake system.



Check for correct brake pedal height. (See page
8-34.) If the pedal height is incorrect, have a
Yamaha dealer adjust it.



Check the operation of the lever and pedal.
They should move smoothly and there should
be a firm feeling when the brakes are applied. If
not, have a Yamaha dealer check the brake sys-
tem.

Brake fluid level

Check the brake fluid level. Add fluid if necessary.
(See page 8-31.)

Brake fluid leakage

Check to see if any brake fluid is leaking out of the
pipe joints or brake fluid reservoirs. Apply the
brakes firmly for one minute. If there is any leak-
age, have a Yamaha dealer check the brake sys-
tem.

Specified brake fluid:

DOT 4

U2LS62E0.book Page 4 Thursday, February 25, 2016 8:44 AM

«
...
56
57
58
59
60
...
»

Содержание YFM700RSBH

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM700RSBH

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды